Toshiba PROSEC T3H user manual Expanded Functions

Page 71

2. Expanded Functions

Ethernet

IP address = 133.113.98.10

T3H (self-station)

F5000

F5001

T3H (target-station)

D4000

D4001

F5199

D4199

When R0030 is ON, 200 words data starting with D4000 of the T3H on which EN311 (IP address = 133.113.98.10) is installed, is read and stored in F5000 and after.

When the operation is completed, the status is set in RW060 and instruction output comes ON.

Note

•Keep the input ON until the output comes ON.

•This instruction becomes error complete in the following cases. (ERF = S0051 is set to ON)

(1)Target station No. is invalid. (for S20LP)

(2) Invalid register designation. (In case of T and C registers, T → T and C → C is only possible)

(3)Source/destination register address range is out of valid range.

(4)Destination register is write-protected.

(5)Response time-out is occurred.

(6)If expanded F register is designated;

-when MMR setting is not made.

-when IC card is not installed.

-when IC card is used to store program.

-when IC card is write-protected. (for destination)

•By using SW067, self-station’s register write-protect is available.

SW067

F	9	8	7	6	5	4	3	2	1	0
	SW	C	T		F	D	RW	LW	W	YW

	0: Write enable	Both F register in CPU and
	1: Write protect
		expanded F register in IC card

•Resetting the status register (operand B) is necessary at the first scan.

•When using the TOSLINE-S20LP or Ethernet module (EN311), read the manual for these network modules.

User’s Manual 69

Image 71

Contents USER’S Manual Important Information Hazard Classifications General InformationWiring Safety Precautions InstallationOperation Maintenance Safety Label Vac About This ManualTerminology T3 manualsContents Prosec T3H Section T3H Overview Introducing the T3H Differences between T3H and T3 Two types of T3H CPU modules are available T3H components CPU moduleStatus LEDs RAM/ROM switchMode control switch IC memory card slot Battery coverProgrammer port Computer link portExpansion interface module CPU T3H CPUCH1 CH2 Expansion cable Power supply moduleRack Following types of I/O modules are available O moduleAscii Data transmission moduleModule internal current consumption TOSLINE-S20LPRAS Specifications Functional specificationsSFC Instruction execution speed Dtst TeorTenr TestTrst SETRST TsetTAN PID2SIN COSInstruction execution speed cont’d Shown below Section Expanded Functions System operation Auto-RUN / Standby selection Timer interrupt intervalSaving the sampling trace condition Auxiliary register Expanded registersExternal I/O register Link register TimerLink Global Special register File registerSEND/RECV Expanded FunctionsTOSLINE-S20 Expanded Functions Starting register Expanded file register data read MRADR S T Expanded file register data Write MWExpanded Functions TOSLINE-S20LP loop support Ethernet support Instructions Double-word multiplication and division D∗ Expanded Functions DSV Essential PID PID3Algorithm Control block diagramParameter details ASV ← ISV OperationExpanded Functions Floating point essential PID FPID3 Digital filter PVn = 1− FT⋅ PVC+ FT⋅ PVn − Here ≤ FT ASV differential limit DSV 0 to 100 %/∆ t Data range +1 ⋅C Expanded Functions Expanded data transfer Xfer Type Transfer parameter tableCPU register ↔ Expanded F register IC memory card CPU register ↔ S20/S20LP scan memory CPU register ↔ Eeprom D register When the data writing address range exceeds page boundary MID Network data send SendExpanded Functions S20LP T3H self-station RW100 RW101 RW227 Network data receive Recv Expanded Functions H0A Expanded Functions Prosec T3H Toshiba Corporation