Toshiba PROSEC T3H user manual When the data writing address range exceeds page boundary

Page 63

2. Expanded Functions

Note

•Edge execution modifier is also available for this instruction.

•The XFER instruction is not executed as error in the following cases. (ERF = S0051 is set to ON)

 

Transfer

 

Error cause

 

Between CPU

1)

When the transfer size is 0 or more than 256.

 

registers

2)

When the source/destination table of transfer is out of the valid range.

 

CPU register to

1)

When the transfer size is 0 or more than 256.

 

expanded F register

2)

When the source/destination table of transfer is out of the valid range.

 

 

3)

When IC memory card is not installed or MMR setting is not made.

 

 

4)

When the IC memory card is write-protect state. (for data writing)

 

 

5)

When program is stored in the IC memory card. (detected only T3H)

 

CPU register to

1)

When the transfer size is 0 or more than 256.

 

S20/S20LP

2)

When the source/destination table of transfer is out of the valid range.

 

 

3)

When channel designation is other than 1 or 2. (other than 1 for T2)

 

 

4)

When S20/S20LP is not installed or not allocated.

 

 

5)

When status flag area is not sufficient.

 

 

6)

When an odd address is designated as the leading address in the case of

 

 

 

S20/S20LP is set as double-word access.

 

 

7)

When the transfer size is odd address in the case of S20/S20LP is set as

 

 

 

double-word access.

 

 

8)

When the S20/S20LP module is not normal.

 

CPU register to

1)

When the transfer size is 0 or more than 256.

 

EEPROM

2)

When the source/destination table of transfer is out of the valid range.

 

 

3)

When the data writing address range exceeds page boundary.

 

 

4)

When this instruction is executed during EEPROM access inhibited (10 ms).

 

 

5)

When the CPU does not have EEPROM.

 

Others

1)

When source/destination designation is invalid.

 

 

2)

When an invalid transfer combination is designated.

 

 

3)

When the index modification is used for an operand and register boundary

 

 

 

error is occurred as the result of the index modification. (in this case, the

 

 

 

instruction output comes OFF)

 

 

 

 

 

 

 

 

 

 

User’s Manual 61

Page 62 Page 64
Image 63
Page 62 Page 64
Contents USER’S Manual Important Information Hazard Classifications General InformationWiring Safety Precautions InstallationOperation Maintenance Safety Label Vac About This ManualTerminology T3 manualsContents Prosec T3H Section T3H Overview Introducing the T3H Differences between T3H and T3 Two types of T3H CPU modules are available T3H components CPU moduleRAM/ROM switch Mode control switchStatus LEDs IC memory card slot Battery coverProgrammer port Computer link portExpansion interface module T3H CPU CH1 CH2CPU Power supply module RackExpansion cable Following types of I/O modules are available O moduleAscii Data transmission moduleModule internal current consumption TOSLINE-S20LPSpecifications Functional specifications SFCRAS Instruction execution speed Dtst TeorTenr TestTrst SETRST TsetTAN PID2SIN COSInstruction execution speed cont’d Shown below Section Expanded Functions System operation Auto-RUN / Standby selection Timer interrupt intervalSaving the sampling trace condition Expanded registers External I/O registerAuxiliary register Link register TimerLink Global Special register File registerSEND/RECV Expanded FunctionsTOSLINE-S20 Expanded Functions Starting register Expanded file register data read MRADR S T Expanded file register data Write MWExpanded Functions TOSLINE-S20LP loop support Ethernet support Instructions Double-word multiplication and division D∗ Expanded Functions DSV Essential PID PID3Algorithm Control block diagramParameter details ASV ← ISV OperationExpanded Functions Floating point essential PID FPID3 Digital filter PVn = 1− FT⋅ PVC+ FT⋅ PVn − Here ≤ FT ASV differential limit DSV 0 to 100 %/∆ t Data range +1 ⋅C Expanded Functions Expanded data transfer Xfer Type Transfer parameter tableCPU register ↔ Expanded F register IC memory card CPU register ↔ S20/S20LP scan memory CPU register ↔ Eeprom D register When the data writing address range exceeds page boundary MID Network data send SendExpanded Functions S20LP T3H self-station RW100 RW101 RW227 Network data receive Recv Expanded Functions H0A Expanded Functions Prosec T3H Toshiba Corporation
Top Page Image Contents