Toshiba B-850 owner manual A4.7.3 Magnified Views of Slant Line Pattern, Letter

Page 106

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.7 Additional Information

A4.7.2 Maintenance Counter/Parameter Check Print Sample and Descriptions (Cont.)

No.

Item

Contents

(34)

Printer IP address

***.***.***.***

(35)

Gateway IP address

***.***.***.***

(36)

Subnet mask

***.***.***.***

(37)

True type font registration area size

0 KB to 896 KB (unit of 64 KB)

(38)

External character registration area size

0 KB to 896 KB (units of 64 KB)

(39)

Basic file store area size

0 KB to 896 KB (units of 64 KB)

(40)

PC saving area size

0 KB to 896 KB (units of 64 KB)

(41)

PCL Emulation

ON: Available

OFF: Unavailable

 

 

(42)

Print speed for PCL emulation

4”/sec.

2”/sec.

 

 

 

 

NONE: None

(43)

Sensor type for PCL emulation

REFLECT: Black mark sensor

 

 

TRANS: Feed gap sensor

(44)

Printing mode for PCL emulation

TRANSFR: Thermal transfer

DIRECT: Thermal direct

 

 

(45)

Issue mode for PCL emulation

[S] NO CUT: Batch mode with no cut

[C]WITH CUT: Cut mode

 

 

 

 

A4

(46)

Media size for PCL emulation

LEGAL

LETTER

 

 

 

 

User

 

 

ON: Available

(47)

Socket port number

OFF: Unavailable

 

 

Port No. 0 to 65535

(48)

BASIC interpreter setting

ON: Available

OFF: Unavailable

 

 

(49)

BASIC interpreter trace setting

ON: Available

OFF: Unavailable

 

 

A4.7.3 Magnified Views of Slant Line Pattern

∙1-dot Slant Line (Black Area Ratio: 16.7%)

∙3-Dot Slant Line (Black Area Ratio: 16.7%)

A4-30

Page 105 Page 107
Image 106
Page 105 Page 107
Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Product Overview Features UnpackingIntroduction Accessories Appearance DimensionsFront View Rear View Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer DownSetting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Driver Download Installing the Printer DriversSystem Requirements SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingTransmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump ModeCleaning MaintenancePrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media „Threshold setting procedure Threshold SettingFeed key A1.1 Printer Appendix 1 SpecificationsModel 852-TS12-QQ A1.3.1 Media Type A1.2 OptionsA1.3 Media LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewPrinting mode selection A4.3 Self-Diagnostic TestMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorBlack Mark Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Feed Gap SensorA4.5 Test Print Print Condition SettingTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test PrintPrinting Mode Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionPaper Feed Selection Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsNon-Printing CharactersBarcode Factory TestA4.6 PCL Emulation Setting Auto PrintPrint Speed Emulation ON/OFF SelectionSensor Type Selection Media Width Setting Issue Mode SelectionMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page Page EO1-33029C
Related manuals
Manual 288 pages 53.68 Kb
Top Page Image Contents