Toshiba B-850 owner manual Index

Page 113

INDEX

R

Reflective sensor A1-4

Resolution A1-1

RESTART key 1-4, 4-1

Ribbon 2-13, 5-2, A1-5

Ribbon holder 1-4

Ribbon supply roll 2-13

Ribbon take up roll 2-13

Ribbon width A1-5

Rotation A1-1

RS-232C 1-3, 2-2, 2-4, A3-1

S

Self diagnostic test	A4-2, A4-3, A4-4, A4-24
Sensor 2-12, 5-1
Sensor adjust gear	2-12

Serial interface 1-3

Supply Holder Frame 2-3, 2-9

Supply Holder Locking Knob 2-7, 2-8 Supply Holder Unit 1-2, 1-3, 2-7 Supply voltage A1-1

T

Tag A1-2

Tear off mode 3-1

Test print 2-15, A4-2, A4-13

Thermal direct A1-1

Thermal transfer A1-1

Threshold setting 6-4

Transmissive sensor A1-3

Two dimensional code A1-1

W

Weight A1-1

EO1-33029

INDEX

Image 113

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Introduction Features UnpackingProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Down PrinterSetting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon COM Inserting the Optional Pcmcia CardsTest Print At the same time Test Print Overview Operating Modes Printer OperationOperating Modes System Requirements Installing the Printer DriversDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details TabTransmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options TabTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line ModeDump Mode Operation ResetPrint Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer A1.3 Media A1.2 OptionsA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System ModeA4.2 Overview If the power is turn on whileMaintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Print head element check Self-Diagnostic Test and the result print outA4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine AdjustmentCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContBlack Mark Sensor Feed Gap SensorTest Pattern Selection Print Condition SettingA4.5 Test Print Specifying the Print Condition for the Test Print Issue Count SettingSensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dotsBarcode CharactersNon-Printing Factory TestAuto Print A4.6 PCL Emulation SettingSensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsBar code GlossariesPre-printed media Index Index Page Page EO1-33029C

Related manuals

Manual 288 pages 53.68 Kb