Toshiba B-850 owner manual A4.2 Overview, If the power is turn on while

Page 78

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.2 Overview

A4.2 Overview

IMPORTANT!

If the power is turn ON while

pressing and holding the [FEED] and [PAUSE] keys at the same time, the printer will enter the System Mode intended for Service

System Mode consists of four main menus: Self-Diagnostic Test, Printer Parameter Fine Adjustment, Test Print and PCL Emulation Setting.

While pressing the [FEED] and [PAUSE] keys at the same time, turn onon the printer. Hold both keys until “<1>DIAG. Vx.x” message appears on the display.

Personnel.

In addition to the menus shown in the chart on the right, the following menus are also displayed in the System Mode for Service Personnel: <2>PARAMETER SET <5>SENSOR ADJ.

<6>RAM CLEAR

<7>IP ADDRESS

Please do not change the parameter settings for these items, as doing so may cause the printer to malfunction.

If you should accidentally enter the System Mode for Service Personnel, just turn the power off. If you should change the settings by accident and the printer malfunctions, please contact your nearest TOSHIBA TEC service representative.

NOTE:

∙System Mode menus can be selected with the [RESTART] or [FEED] key.

[RESTART]

!',$*9[[

[FEED] [RESTART]

!$'-8676(7

[FEED] [RESTART]

!7(6735,17

[FEED] [RESTART]

!3&/(08/$7,21

[FEED]

This is the start of the Self- Diagnostic Test menu.

This is the start of the Printer Parameter Fine Adjustment menu.

This is the start of the Test Print menu.

This is the start of the PCL Emulation menu.

∙Pressing the [PAUSE] key allows you to enter the sub menus of each System Mode menu. Flowcharts of each menu’s sub menus are provided on the following pages.

A4- 2

Image 78

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Features Unpacking Product OverviewIntroduction Accessories Dimensions AppearanceFront View Rear View Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer DownSetting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Driver Download Installing the Printer DriversSystem Requirements SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingTransmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump ModeMaintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.3.1 Media Type A1.2 OptionsA1.3 Media LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewA4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorBlack Mark Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Feed Gap SensorPrint Condition Setting A4.5 Test PrintTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test PrintPrint Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsNon-Printing CharactersBarcode Factory TestA4.6 PCL Emulation Setting Auto PrintEmulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page Page EO1-33029C

Related manuals

Manual 288 pages 53.68 Kb