Toshiba B-850 owner manual Threshold Setting, „Threshold setting procedure, Feed key

Page 68

6. TROUBLESHOOTING

EO1-33029

6.4 Threshold Setting

6.4 Threshold Setting

NOTES:

1.If the [PAUSE] key is released within 3 seconds while in pause state, paper will not feed.

2.Failure to feed more than 1.5 labels may result in an incorrect threshold setting.

3.While the Print Head Block is raised, the [PAUSE] key does not work.

4.Errors such as paper end and cutter error are not detected during paper feed.

5.Selecting the Transmissive Sensor(for pre-printed labels) within software commands allows the printer to detect the proper print start position correctly even when using pre-printed labels.

6.If using the transmissive sensor and the printer continues to print out of position even after setting the threshold, adjust the Feed Gap Sensor in the system mode. Reset the threshold again. Make sure that the Transmissive Sensor (for pre-printed labels) is selected in the feed and issue commands.

To maintain a constant print position the printer uses the Transmissive Sensor to detect the gap between labels by measuring the amount of light passing through the media. When the media is pre-printed, the darker (or more dense) inks can interfere with this process causing paper jam errors. To get around this problem a minimum threshold can be set for the sensor in the following way.

„Threshold setting procedure

1.Turn the power ON. The printer is in stand by mode.

21/,1(

2.Load a media roll.

3.Press the [PAUSE] key.

3$86(

4.The printer enters the pause mode.

5.Press and hold the [PAUSE] key for at least 3 seconds in the pause state.

75$160,66,9(

6.The sensor type is displayed.

7.To select the Reflective Sensor (Black Mark Sensor), press the

[FEED] key.

5()/(&7,9(

8.To select the Transmissive Sensor (Feed Gap Sensor), press the [FEED] key again.

75$160,66,9(

9.Press and hold the [PAUSE] key until more than 1.5 labels (tags) have been advanced.

The media is advanced until the [PAUSE] key is released. (Threshold setting is completed by this operation.)

3$86(

10.Press the [RESTART] key.

21/,1(

11.The printer is in stand-by.

12.Send an issue command from the PC to the printer.

21/,1(

6- 4

Image 68

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Introduction Features UnpackingProduct Overview Accessories Front View Rear View DimensionsAppearance Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer DownSetting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Installing the Printer Drivers System RequirementsDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingTransmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump ModePrint Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewMaintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorA4.4 Printer Parameter Fine Adjustment Cont Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorBlack Mark Sensor Feed Gap SensorTest Pattern Selection Print Condition SettingA4.5 Test Print Issue Count Setting Specifying the Print Condition for the Test PrintSensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsCharacters BarcodeNon-Printing Factory TestA4.6 PCL Emulation Setting Auto PrintSensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page Page EO1-33029C

Related manuals

Manual 288 pages 53.68 Kb