Toshiba B-850 owner manual A4.4 Printer Parameter Fine Adjustment

Page 81

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.4 Printer Parameter Fine Adjustment

A4.4 Printer Parameter Fine Adjustment

Outline of Printer Parameter

Fine Adjustment

In the Printer Parameter Fine Adjustment mode, Fine adjustments can be performed for each parameter, such as Print tone, Print start position, Threshold, etc. which are set by the PC command. This is useful when using several types of media in rotation or when the print start position or cut position requires fine adjustments.

The Printer Parameter Fine Adjustment menu contains the following.

!$'-8676(7

[PAUSE]
)(('$'-PP	Feed Length Fine Adjustment
[PAUSE]
&87$'-PP	Cut Position Fine Adjustment
[PAUSE]
%$&.$'-PP	Back Feed Length Fine Adjustment
[PAUSE]
;$'-867PP	X Axis Fine Adjustment
[PAUSE]
721($'-7!	Print Tone Fine Adjustment
[PAUSE]	(Thermal Transfer)
[PAUSE]
721($'-'!	Print Tone Fine Adjustment
[PAUSE]	(Thermal Direct)
[PAUSE]
5%1$'-):!	Ribbon Motor Drive Voltage	Fine
5%1$'-):!	Adjustment (Rewind Motor)
[PAUSE]	Adjustment (Rewind Motor)
[PAUSE]
5%1$'-%.!	Ribbon Motor Drive Voltage	Fine
5%1$'-%.!	Adjustment (Feed Motor)
[PAUSE]	Adjustment (Feed Motor)
[PAUSE]
7+5(6+2/'5!9	Threshold Fine Adjustment (Black
[PAUSE]	Mark Sensor)
[PAUSE]

7+5(6+2/'7!9 Threshold Fine Adjustment (Feed

[PAUSE]

Gap Sensor)

A4- 5

Image 81

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents On Line Mode Features Unpacking Product OverviewIntroduction Accessories Dimensions AppearanceFront View Rear View Interior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Down PrinterSetting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon COM Inserting the Optional Pcmcia CardsTest Print At the same time Test Print Overview Operating Modes Printer OperationOperating Modes System Requirements Installing the Printer DriversDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details TabTransmission Retry ∙ In Print to the following port, click the port just mapped Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Cont. Bar Code Options Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options TabTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line ModeDump Mode Operation ResetMaintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.3 Media A1.2 OptionsA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System ModeA4.2 Overview If the power is turn on whileA4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Print head element check Self-Diagnostic Test and the result print outA4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine AdjustmentCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContBlack Mark Sensor Feed Gap SensorPrint Condition Setting A4.5 Test PrintTest Pattern Selection Specifying the Print Condition for the Test Print Issue Count SettingPrint Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dotsBarcode CharactersNon-Printing Factory TestAuto Print A4.6 PCL Emulation SettingEmulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsBar code GlossariesPre-printed media Index Index Page Page EO1-33029C

Related manuals

Manual 288 pages 53.68 Kb