Toshiba B-SX4T owner manual Batch mode, Strip mode Option, STANDARD/PEEL OFF position

Page 21

2. PRINTER SETUP

ENGLISH VERSION EO1-33058

2.4 Loading the Media

2.4Loading the Media (Cont.)

12.There are four issue modes available on this printer. How to set the media for each mode is provided below.

Batch mode

In the batch mode, the media is continuously printed and fed until the number of labels/tags specified in the issue command have been printed.

NOTES:

1.Be sure to set the Selection Switch to STANDARD/ PEEL OFF position.

2.The backing paper is easier to feed back to the Take-Up Spool if the Front Plate is removed.

3.Fit the Take-Up Clip so that the longer side of the clip is fitted into the shallow groove in the Take-Up Spool.

4.The backing paper can be wound directly onto the Take- up Spool or a paper core. When using the Take-up Spool, detach the Holder Stopper by removing the B- 3x4 screw. Otherwise, it may be difficult to pull out the wound backing paper roll.

Holder Stopper

B-3x4 Screw

Take-up Spool

Take-up Clip

When using a paper core, put the core on the Take-up Spool with the Holder Stopper on it, and attach the top edge of the backing paper to the core with adhesive tape. The Take-up Clip is not necessary.

This winding method is applicable to the Built-in Rewinder mode.

Strip mode (Option)

When the optional Strip Module is fitted, the backing paper is automatically removed from the label at the Strip Plate as each label is printed.

(1)Remove enough labels from the leading edge of the media to leave 500mm of backing paper free.

(2)Insert the backing paper under the Strip Plate.

(3)Wind the backing paper onto the Take-up Spool and fix it in position with the Take-up Clip. (Wind the paper counterclockwise around the spool as this is the direction it rotates.)

(4)Rotate the Take-up Spool anti-clockwise a few times to remove any slack in the backing paper.

(5)Set the Selection Switch mounted on the Rewinder Assembly to

STANDARD/PEEL OFF position.

Take-up Spool

Front Plate

Take-up Clip

Black Screw Strip Plate Backing Paper

E2- 7

Image 21

Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction Features UnpackingNo FM1647000 AccessoriesDoc. No. EO2-33021 Quality Control Report 1 sheetFront View DimensionsRear View Following chaptersInterior Operation PanelOption Name Type Description OptionsSetup Flow Printer SetupProcedure ReferenceInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionRemove the Locking Screw that secures the Media Sensor Batch mode Strip mode OptionSTANDARD/PEEL OFF position Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterParagraphs outline how to insert Pcmcia cards Pcmcia CardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed SequentiallyUse the Feed or Restart key to select a desired option Character Code SelectionAfter selecting a character code, press the Pause key Character Zero SelectionAfter selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause keyStop Bit Selection Parity SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyFeed key Head Up Cut/Rewinder SelectionSolenoid Type Selection After selecting the solenoid type, press the Pause keyRibbon Saving Function Selection Control Code Selection After selecting the Strip Wait Status, press the Pause key Strip Wait Status SelectionFeed Key Function Selection After selecting the Feed key function, press the Pause keyAfter selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause keyAfter selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Ribbon Near End SelectionCentronics Interface Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Pre-Strip SelectionAfter selecting the Pre-strip function, press the Pause key Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key System Mode Password Setting Print Head Type SelectionAfter selecting a print head type, press the Pause key After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually setFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyMedia has run out Load new media. Then press Error Messages Problems/Cause SolutionsMedia is slack Take up any slack in the media Ribbon has run out Load a new ribbon. Then pressPossible Problems Possible Problems Causes SolutionsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter blade Refer to .1 Media⇒Section Removing Jammed Media Printer Specifications This section describes the printer specificationsModel SX4T-GS20-QM-R Media Supply SpecificationsMedia Type LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageWrong password was entered Printer is waiting for a password to Be enteredBase LAN Board is being Initialized Printer did not succeed in writingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard LAN cable Physical Layer100BASE-TX UTP category Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-U1-EU RFID-U1-USRFID-H1-QM SX704-RFID-U2-US-RAppendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper See Black mark sensorMedia and ribbon See Feed gap sensor3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E