Toshiba B-SX4T owner manual Turning the Printer, Turning on the Printer

Page 26

2. PRINTER SETUP

ENGLISH VERSION EO1-33058

2.7 Turning the Printer ON/OFF

2.7Turning the Printer

ON/OFF

2.7.1 Turning ON the Printer

CAUTION!

Use the power switch to turn the printer On/Off. Plugging or unplugging the Power Cord to turn the printer On/Off may cause fire, an electric shock, or damage to the printer.

When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer.

1.To turn ON the printer power, press the Power Switch as shown in the diagram below. Note that ( ) is the power ON side of the switch.

Power Switch

NOTE:

If a message other than ON LINE appears on the display or the ERROR LED lamp is illuminated, go to Section 5.1, Error Messages.

2.Check that the ON LINE message appears in the LCD Message Display and that the ON LINE and POWER LED lights are illuminated.

2.7.2Turning OFF the Printer 1. Before turning off the printer Power Switch verify that the ON LINE message appears in the LCD Message Display and that the ON LINE LED light is on and is not flashing.

CAUTION!

1.Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer.

2.Do not turn off the printer power while the ON LINE lamp is blinking as this may cause damage to your computer.

2.To turn OFF the printer power press the Power Switch as shown in the

diagram below. Note that ( ) is the power OFF side of the switch.

Power Switch

E2-12

Image 26

Contents SX4T Series CE Compliance for EU only VorsichtSX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Unpacking Product OverviewDoc. No. EO2-33021 AccessoriesNo FM1647000 Quality Control Report 1 sheetRear View DimensionsFront View Following chaptersOperation Panel InteriorOptions Option Name Type DescriptionProcedure Printer SetupSetup Flow ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Remove the Locking Screw that secures the Media Sensor Setting the Feed Gap Sensor positionSetting the Black Mark Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Option Built-in rewinder mode Option Cut mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterFollowing Pcmcia cards or equivalent can be used Paragraphs outline how to insert Pcmcia cardsPcmcia Cards How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message SequentiallyAfter selecting a character code, press the Pause key Character Code SelectionUse the Feed or Restart key to select a desired option Character Zero SelectionData Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause keyFlow Control Code Selection Stop Bit SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause keyHead Up Cut/Rewinder Selection Feed keyRibbon Saving Function Selection Solenoid Type SelectionAfter selecting the solenoid type, press the Pause key Control Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause keyEuro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause keyCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause keyAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Ribbon Near End Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Centronics Interface SelectionPlug & Play Selection After selecting the Pre-strip function, press the Pause key Label End/Ribbon End SelectionPre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection After selecting a print head type, press the Pause key System Mode Password SettingPrint Head Type Selection Use the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause keyRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Select the sensor to be adjusted by using the Feed key Threshold SettingJam errors Manually setFeed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyMedia is slack Take up any slack in the media Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Ribbon has run out Load a new ribbon. Then pressRibbon is not loaded properly Load the ribbon properly Possible ProblemsPossible Problems Causes Solutions ⇒Section Cutter blade is dirty Clean the cutter bladeRefer to .1 Media Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications SX4T-GS20-QM-R Media Type Supply SpecificationsMedia LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsBase LAN Board is being Printer is waiting for a password to Be enteredWrong password was entered Initialized Printer did not succeed in writingFollowing message appears Appendix 2 Interface Parallel interface Centronics StandardConnector PINSerial interface Standard 100BASE-TX UTP category Physical LayerLAN cable Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU SX704-RFID-U2-US-RAt least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Media and ribbon See Black mark sensorDevice used to remove labels from the backing paper See Feed gap sensorIndex 3-1, A1-1Index Waste Recycling information for users EO1-33058E