Toshiba B-SX4T owner manual How to enter the System Mode

Page 28

2. PRINTER SETUP

ENGLISH VERSION EO1-33058

2.9 Setting an Operating Environment

2.9Setting an Operating Environment

LCD Message

Display

FEED key

RESTART key

PAUSE key

ON LINE

[PAUSE]

PAUSE

Hold down [RESTART] for 3 sec.

<1>RESET

[FEED] [RESTART]

<2>PARAMETER SET

[FEED] [RESTART]

<3>ADJUST SET

[FEED] [RESTART]

<4>DUMP MODE

[FEED] [RESTART]

<5>EXPAND MODE

[FEED] [RESTART]

Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings.

Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment.

NOTE:

Incorrect settings can cause the printer to function erroneously. If you have any problems with the parameter settings, please contact your nearest TOSHIBA TEC service representative.

For the settings this manual does not cover, please contact your nearest TOSHIBA TEC service representative, or refer to the B-SX4T/SX5T Series Key Operation Specification stored in the CD-ROM.

How to enter the System Mode

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

The System Mode consists of the following menus.

<1>RESET	This menu is used to clear print data sent from a
	PC and return the printer to an idle state.
	Refer to Section 3.3 Reset.
<2>PARAMETER SET	This menu is used to set the printer parameters.
	Refer to Section 2.9.1 Parameter Setting.
<3>ADJUST SET	This menu is used to make a fine adjustment of a
	print start position, cut position, etc.
	Refer to Section 2.12 Position and Print Tone
	Fine Adjustment.
<4>DUMP MODE	This menu is used to print the data in the receive
	buffer for debug.
	Refer to Section 2.9.2 Dump Mode Setting.
<5>EXPAND MODE	This menu is used to start the program for
	BASIC mode.
	Refer to Section 2.9.3 BASIC Expansion
	Mode.
	NOTES:

1.System Mode menus can be selected with the [RESTART] or [FEED] key.

2.To enter each of the above System Mode menus, press the [PAUSE] key when the menu is displayed.

3.If the [PAUSE] key is pressed with “<1>RESET” being displayed, the printer will turn to an idle state and the message will change to “ONLINE”.

E2-14

Image 28

Contents SX4T Series CE Compliance for EU only VorsichtSX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Introduction Features Unpacking Product OverviewAccessories No FM1647000Doc. No. EO2-33021 Quality Control Report 1 sheetDimensions Front ViewRear View Following chaptersOperation Panel InteriorOptions Option Name Type DescriptionPrinter Setup Setup FlowProcedure ReferenceInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionRemove the Locking Screw that secures the Media Sensor Strip mode Option Batch modeSTANDARD/PEEL OFF position Built-in rewinder mode Option Cut mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards Paragraphs outline how to insert Pcmcia cardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Parameter Setting While 2PARAMETER SET is displayed on the LCD MessageTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a character code, press the Pause key Character Zero SelectionBaud Rate Selection After selecting a baud rate, press the Pause keyData Length Selection After selecting a data length, press the Pause keyParity Selection Stop Bit SelectionFlow Control Code Selection LCD Language Selection After selecting a language, press the Pause keyAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyHead Up Cut/Rewinder Selection Feed keyAfter selecting the solenoid type, press the Pause key Solenoid Type SelectionRibbon Saving Function Selection Control Code Selection Strip Wait Status Selection After selecting the Strip Wait Status, press the Pause keyFeed Key Function Selection After selecting the Feed key function, press the Pause keyKanji Code Selection After selecting a Kanji code, press the Pause keyEuro Code Selection After selecting a Euro code, press the Pause keyAuto Print Head Check Selection After selecting auto print head check, press the Pause keyCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyInput Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type SelectionPlug & Play Selection Centronics Interface SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Label End/Ribbon End SelectionAfter selecting the Pre-strip function, press the Pause key Reverse Feed Speed Selection Maxi Code Specification SelectionAfter selecting the Back Feed Speed, press the Pause key Print Head Type Selection System Mode Password SettingAfter selecting a print head type, press the Pause key Dump Mode Setting After selecting the receive buffer, press the Pause keyUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyReceive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Jam errorsSelect the sensor to be adjusted by using the Feed key Manually setFeed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Media has run out Load new media. Then pressMedia is slack Take up any slack in the media Ribbon has run out Load a new ribbon. Then pressPossible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Refer to .1 Media Cutter blade is dirty Clean the cutter blade⇒Section Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel SX4T-GS20-QM-R Supply Specifications MediaMedia Type LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsPrinter is waiting for a password to Be entered Wrong password was enteredBase LAN Board is being Initialized Printer did not succeed in writingFollowing message appears Appendix 2 Interface Parallel interface Centronics StandardConnector PINSerial interface Standard Physical Layer LAN cable100BASE-TX UTP category Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM SX704-RFID-U2-US-RWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries See Black mark sensor Device used to remove labels from the backing paperMedia and ribbon See Feed gap sensorIndex 3-1, A1-1Index Waste Recycling information for users EO1-33058E