Toshiba B-SX4T owner manual Care/Handling of Media and Ribbon, Ribbon type Description

Page 101

7. SUPPLY SPECIFICATIONS

ENGLISH VERSION EO1-33058

7.4 Care/Handling of Media and Ribbon

7.3 Recommended Media and Ribbon Types (Cont.)

Ribbon type

Description

Smear-less ribbon (Wax resin ribbon)

Good match for coated paper. The printed image will resist water and

 

light rubbing.

Scratch and solvent resistance ribbon

Very good match for plastic films (synthetic paper, PET, polyimide,

 

etc.)

 

Scratch and solvent resistance

 

Heat resistance with PET and polyimide.

Combination of Media and Ribbon

Media type

Vellum paper and label

Coated paper

Ribbon type

 

 

Smear-less ribbon (wax-

 

{

resin ribbon)

 

 

 

Scratch/solvent

 

 

resistance ribbon

 

 

Plastic films

{

{: Good match

7.4 Care/Handling of Media and Ribbon

CAUTION!

Be sure to carefully review and understand the Supply Manual. Use only media and ribbons that meet specified requirements. Use of non-specified media and ribbons may shorten the head life and result in problems with bar code readability or print quality. All media and ribbons should be handled with care to avoid any damage to the media, ribbons or printer. Read the guidelines in this section carefully.

Do not store the media or ribbon for longer than the manufacturer’s recommended shelf life.

Store media rolls on the flat end. Do not store them on the curved sides as this might flatten that side causing erratic media advance and poor print quality.

Store the media in plastic bags and always reseal after opening. Unprotected media can get dirty and the extra abrasion from the dust and dirt particles will shorten the print head life.

Store the media and ribbon in a cool, dry place. Avoid areas where they would be exposed to direct sunlight, high temperature, high humidity, dust or gas.

The thermal paper used for direct thermal printing must not have specifications which exceed Na+ 800 ppm, K+ 250 ppm and Cl- 500 ppm.

Some ink used on pre-printed media may contain ingredients which shorten the print head’s product life. Do not use labels pre-printed with ink which contain hard substances such as carbonic calcium (CaCO3) and kaolin (Al2O3, 2SiO2, 2H2O).

For further information, please contact your local distributor or your media and ribbon manufacturers.

E7- 7

Image 101
Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction Features UnpackingNo FM1647000 AccessoriesDoc. No. EO2-33021 Quality Control Report 1 sheetFront View DimensionsRear View Following chaptersInterior Operation PanelOption Name Type Description OptionsSetup Flow Printer SetupProcedure ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Remove the Locking Screw that secures the Media Sensor Setting the Feed Gap Sensor positionSetting the Black Mark Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Option Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterFollowing Pcmcia cards or equivalent can be used Paragraphs outline how to insert Pcmcia cardsPcmcia Cards How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed SequentiallyUse the Feed or Restart key to select a desired option Character Code SelectionAfter selecting a character code, press the Pause key Character Zero SelectionAfter selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause keyFlow Control Code Selection Stop Bit SelectionParity Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionAfter selecting the solenoid type, press the Pause key Control Code Selection After selecting the Strip Wait Status, press the Pause key Strip Wait Status SelectionFeed Key Function Selection After selecting the Feed key function, press the Pause keyAfter selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause keyAfter selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Expansion I/O Interface Type Selection Ribbon Near End SelectionAfter selecting a Plug & Play, press the Pause key Centronics Interface SelectionPlug & Play Selection After selecting the Pre-strip function, press the Pause key Label End/Ribbon End SelectionPre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection After selecting a print head type, press the Pause key System Mode Password SettingPrint Head Type Selection After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually setFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModePress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyMedia has run out Load new media. Then press Error Messages Problems/Cause SolutionsMedia is slack Take up any slack in the media Ribbon has run out Load a new ribbon. Then pressRibbon is not loaded properly Load the ribbon properly Possible ProblemsPossible Problems Causes Solutions ⇒Section Cutter blade is dirty Clean the cutter bladeRefer to .1 Media Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications SX4T-GS20-QM-R Media Supply SpecificationsMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageWrong password was entered Printer is waiting for a password to Be enteredBase LAN Board is being Initialized Printer did not succeed in writingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard LAN cable Physical Layer100BASE-TX UTP category Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-U1-EU RFID-U1-USRFID-H1-QM SX704-RFID-U2-US-RAt least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper See Black mark sensorMedia and ribbon See Feed gap sensor3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E