Toshiba B-SX4T owner manual Position and Print Tone Fine Adjustment, Feed Amount Fine Adjustment

Page 70

2. PRINTER SETUP

ENGLISH VERSION EO1-33058

2.12 Position and Print Tone Fine Adjustment

2.12Position and Print Tone Fine Adjustment

<3>ADJUST SET

[PAUSE]

<3>ADJUST SET FEED ADJ.+10.0mm

[PAUSE]

<3>ADJUST SET CUT ADJ. +10.0mm

[PAUSE]

<3>ADJUST SET BACK ADJ. +5.0mm

[PAUSE]

<3>ADJUST SET

X ADJUST +50.0mm

[PAUSE]

<3>ADJUST SET TONE ADJ.<T> +3

[PAUSE]

<3>ADJUST SET TONE ADJ.<D> -2

[PAUSE]

<3>ADJUST SET RBN ADJ <FW> -10

[PAUSE]

<3>ADJUST SET RBN ADJ <BK> -5

[PAUSE]

<3>ADJUST SET THRESHOLD<R>1.0V

[PAUSE]

<3>ADJUST SET THRESHOLD<T>1.4V

[PAUSE]

This section describes how to fine adjust a print start position, cut/strip position, reverse feed amount, print tone, and ribbon motor torque.

When a fine adjustment is required, such as print start position, print tone, etc, follow the procedure below.

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

4.Press the [FEED] or [RESTART] key until “<3>ADJUST SET” appears on the LCD Message Display.

5.When “<3>ADJUST SET” appears, press the [PAUSE] key to enter the Parameter Fine Adjustment Mode.

The Parameter Fine Adjustment Mode contains the following sub menus. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.

(1)Feed Amount Fine Adjustment:

Feed amount to the print start position is fine adjusted.

(2)Cut/Strip Position Fine Adjustment:

Cut position or strip position is fine adjusted.

(3)Reverse Feed Amount Fine Adjustment: Reverse feed amount is fine adjusted.

(4)X-coordinate Fine Adjustment:

X-coordinate of a print position is fine adjusted.

(5)Print Tone Fine Adjustment (Thermal transfer): Print tone is fine adjusted for thermal transfer mode.

(6)Print Tone Fine Adjustment (Thermal direct): Print tone is fine adjusted for thermal direct mode.

(7)Ribbon Motor Drive Voltage Fine Adjustment (Take-up motor):

Drive voltage of the ribbon take-up motor is fine adjusted.

(8)Ribbon Motor Drive Voltage Fine Adjustment (Feed motor) Drive voltage of the ribbon feed motor is fine adjusted.

(9)Threshold Fine Adjustment (Black mark sensor):

Threshold for the black mark sensor is fine adjusted. See Section 2.13.

(10)Threshold Fine Adjustment (Feed gap sensor):

Threshold for the feed gap sensor is fine adjusted. See Section 2.13.

NOTE:

The printer driver’s properties screen also has Parameter Fine Adjustment menu.

E2-56

Page 69 Page 71
Image 70
Page 69 Page 71
Contents SX4T Series CE Compliance for EU only VorsichtSX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Unpacking Product OverviewDoc. No. EO2-33021 AccessoriesNo FM1647000 Quality Control Report 1 sheetRear View DimensionsFront View Following chaptersOperation Panel InteriorOptions Option Name Type DescriptionProcedure Printer SetupSetup Flow ReferenceInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionRemove the Locking Screw that secures the Media Sensor Strip mode Option Batch modeSTANDARD/PEEL OFF position Built-in rewinder mode Option Cut mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterPcmcia Cards Paragraphs outline how to insert Pcmcia cardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message SequentiallyAfter selecting a character code, press the Pause key Character Code SelectionUse the Feed or Restart key to select a desired option Character Zero SelectionData Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause keyParity Selection Stop Bit SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause keyHead Up Cut/Rewinder Selection Feed keyAfter selecting the solenoid type, press the Pause key Solenoid Type SelectionRibbon Saving Function Selection Control Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause keyEuro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause keyCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause keyInput Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type SelectionPlug & Play Selection Centronics Interface SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Label End/Ribbon End SelectionAfter selecting the Pre-strip function, press the Pause key Reverse Feed Speed Selection Maxi Code Specification SelectionAfter selecting the Back Feed Speed, press the Pause key Print Head Type Selection System Mode Password SettingAfter selecting a print head type, press the Pause key Use the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause keyReceive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Select the sensor to be adjusted by using the Feed key Threshold SettingJam errors Manually setFeed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyMedia is slack Take up any slack in the media Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Ribbon has run out Load a new ribbon. Then pressPossible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Refer to .1 Media Cutter blade is dirty Clean the cutter blade⇒Section Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel SX4T-GS20-QM-R Media Type Supply SpecificationsMedia LabelLabel Detection Area of the Transmissive SensorTag paper with square holes Detection Area of the Reflective Sensor Effective Print Area„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsBase LAN Board is being Printer is waiting for a password to Be enteredWrong password was entered Initialized Printer did not succeed in writingFollowing message appears Appendix 2 Interface Parallel interface Centronics StandardConnector PINSerial interface Standard 100BASE-TX UTP category Physical LayerLAN cable Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU SX704-RFID-U2-US-RWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Media and ribbon See Black mark sensorDevice used to remove labels from the backing paper See Feed gap sensorIndex 3-1, A1-1Index Waste Recycling information for users EO1-33058E
Top Page Image Contents