Toshiba B-SX4T owner manual Precautions, Request Regarding Maintenance

Page 7

Safety Summary

ENGLISH VERSION EO1-33058

 

 

Disconnect

If foreign objects (metal

Disconnect

When unplugging the power cords,

 

 

 

 

fragments, water, liquids) enter

be sure to hold and pull on the plug

 

 

the plug.

the machines, first turn off the

the plug.

portion. Pulling on the cord portion

 

 

 

power switches and disconnect

 

may cut or expose the internal wires

 

 

 

the power cord plugs from the

 

and cause fire or electric shock.

 

 

 

outlet, and then contact your

 

 

 

 

 

authorised TOSHIBA TEC

 

 

 

 

 

representative for assistance.

 

 

 

 

 

Continued use of the machine in

 

 

 

 

 

that condition may cause fire or

 

 

 

 

 

electric shock.

 

 

 

 

Connect a

Ensure that the equipment is

No

Do not remove covers, repair or

 

 

properly grounded. Extension

modify the machine by yourself.

 

 

grounding wire.

disassembling.

 

 

 

cables should also be grounded.

 

You may be injured by high

 

 

 

Fire or electric shock could

 

voltage, very hot parts or sharp

 

 

 

occur on improperly grounded

 

edges inside the machine.

 

 

 

equipment.

 

 

 

 

 

 

 

 

CAUTION This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication.

Precautions

The following precautions will help to ensure that this machine will continue to function correctly.

Try to avoid locations that have the following adverse conditions:

*

Temperatures out of the specification

*

Direct sunlight

*

High humidity

*

Shared power source

*

Excessive vibration

*

Dust/Gas

The cover should be cleaned by wiping with a dry cloth or a cloth slightly dampened with a mild detergent solution. NEVER USE THINNER OR ANY OTHER VOLATILE SOLVENT on the plastic covers.

USE ONLY TOSHIBA TEC SPECIFIED paper and ribbons.

DO NOT STORE the paper or ribbons where they might be exposed to direct sunlight, high temperatures, high humidity, dust, or gas.

Ensure the printer is operated on a level surface.

Any data stored in the memory of the printer could be lost during a printer fault.

Try to avoid using this equipment on the same power supply as high voltage equipment or equipment likely to cause mains interference.

Unplug the machine whenever you are working inside it or cleaning it.

Keep your work environment static free.

Do not place heavy objects on top of the machines, as these items may become unbalanced and fall causing injury.

Do not block the ventilation slits of the machines, as this will cause heat to build up inside the machines and may cause fire.

Do not lean against the machine. It may fall on you and could cause injury.

Care must be taken not to injure yourself with the printer paper cutter.

Unplug the machine when it is not used for a long period of time.

Place the machine on a stable and level surface.

Request Regarding Maintenance

Utilize our maintenance services.

After purchasing the machine, contact your authorised TOSHIBA TEC representative for assistance once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may cause a fire or a malfunction. Cleaning is particularly effective before humid rainy seasons.

Our preventive maintenance service performs the periodic checks and other work required to maintain the quality and performance of the machines, preventing accidents beforehand.

For details, please consult your authorised TOSHIBA TEC representative for assistance.

Using insecticides and other chemicals

Do not expose the machines to insecticides or other volatile solvents. This will cause the cabinet or other parts to deteriorate or cause the paint to peel.

(ii)

Image 7
Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction Features UnpackingQuality Control Report 1 sheet AccessoriesNo FM1647000 Doc. No. EO2-33021Following chapters DimensionsFront View Rear ViewInterior Operation PanelOption Name Type Description OptionsReference Printer SetupSetup Flow ProcedureInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionRemove the Locking Screw that secures the Media Sensor Strip mode Option Batch modeSTANDARD/PEEL OFF position Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards Paragraphs outline how to insert Pcmcia cardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedCharacter Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionParity Selection Stop Bit SelectionFlow Control Code Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionFeed key Head Up Cut/Rewinder SelectionAfter selecting the solenoid type, press the Pause key Solenoid Type SelectionRibbon Saving Function Selection Control Code Selection After selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionInput Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Label End/Ribbon End SelectionAfter selecting the Pre-strip function, press the Pause key Reverse Feed Speed Selection Maxi Code Specification SelectionAfter selecting the Back Feed Speed, press the Pause key Print Head Type Selection System Mode Password SettingAfter selecting a print head type, press the Pause key After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodReceive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsRibbon has run out Load a new ribbon. Then press Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Media is slack Take up any slack in the mediaPossible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Refer to .1 Media Cutter blade is dirty Clean the cutter blade⇒Section Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel SX4T-GS20-QM-R Label Supply SpecificationsMedia Media TypeLabel Detection Area of the Transmissive SensorTag paper with square holes Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messageInitialized Printer did not succeed in writing Printer is waiting for a password to Be enteredWrong password was entered Base LAN Board is beingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard Cable length Segment length Max m Physical LayerLAN cable 100BASE-TX UTP categoryExpansion I/O Interface Option B-7704-IO- QM-R SX704-RFID-U2-US-R RFID-U1-USRFID-U1-EU RFID-H1-QMWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries See Feed gap sensor See Black mark sensorDevice used to remove labels from the backing paper Media and ribbon3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E