Toshiba B-SX4T owner manual For all countries and areas

Page 5

This product is equipped with a wireless communication device,

TEC-RFID-US1 (B-9704-RFID-U1-US-R), TEC-RFID-EU1 (B-9704-RFID-U1-EU-R), TRW-USM-01 (B-SX704-RFID-U2-US-R) TRW-EUM-01 (B-SX704-RFID-U2-EU-R), TRW-AUM-01 (B-SX704-RFID-U2-AU-R)

Please be sure to read the enclosed precaution for handling of wireless communication devices before using this product. Precautions for Handling of Wireless Communication Devices

RFID kit:TEC-RFID-US1 (B-9704-RFID-U1-US-R), TEC-RFID-EU1 (B-9704-RFID-U1-EU-R), TRW-USM-01 (B-SX704-RFID-U2-US-R), TRW-EUM-01 (B-SX704-RFID-U2-EU-R), TRW-AUM-01 (B-SX704-RFID-U2-AU-R)

For all countries and areas

This product is a wireless communication device, and the use of this product is restricted to the following countries or areas. If the product is used in the countries or areas other than the following, you may be punished according to the laws of those countries or areas.

TEC-RFID-US1 (B-9704-RFID-U1-US-R), TRW-USM-01 (B-SX704-RFID-U2-US-R): USA, Canada

TEC-RFID-EU1 (B-9704-RFID-U1-EU-R), TRW-EUM-01 (B-SX704-RFID-U2-EU-R): Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Hungary, Germany, Greece, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, United Kingdom, Norway, Liechtenstein, Iceland, Switzerland TRW-AUM-01 (B-SX704-RFID-U2-AU-R): Australia

For safety

Do not use the product in locations where the use is forbidden, for example in a hospital. When you do not know the forbidden areas, please refer to and follow the medical institution. Otherwise medical equipment may be affected, causing a serious accident.

This product may affect the operation of some implanted cardiac pacemakers and other medically implanted equipment. Pace maker patients should be aware that the use of this product very close to a pacemaker might cause the device to malfunction. If you have any reason to suspect that interference is taking place, immediately turn off the product and contact your TOSHIBA TEC sales agent.

Do not disassemble, modify, or repair the product.

Doing so may cause injury. Also, modification is against the Laws and Regulations for Radio Equipment. Please ask your TOSHIBA TEC sales agent for repair.

For USA

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received , including interference that may cause undesired operation.

Changes or modification not expressly approved by manufacturer for compliance could void the user’s authority to operate the equipment.

For Canada

Operation is subject to the following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference , including interference that may cause undesired operation of the device.

For Europe

Hereby, Toshiba TEC Corporation, declares that this TEC-RFID-EU1 (B-9704-RFID-U1-EU-R), TRW-EUM-01 (B-SX704-RFID-U2-EU-R) are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment uses the radio frequency band which has not been harmonized throughout all EU and EFTA countries, and can be used in the following countries.

Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Hungary, Germany, Greece, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, United Kingdom, Norway, Liechtenstein, Iceland, Switzerland

Page 4 Page 6
Image 5
Page 4 Page 6
Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction Features UnpackingNo FM1647000 AccessoriesDoc. No. EO2-33021 Quality Control Report 1 sheetFront View DimensionsRear View Following chaptersInterior Operation PanelOption Name Type Description OptionsSetup Flow Printer SetupProcedure ReferenceInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Remove the Locking Screw that secures the Media Sensor Setting the Feed Gap Sensor positionSetting the Black Mark Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Option Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterFollowing Pcmcia cards or equivalent can be used Paragraphs outline how to insert Pcmcia cardsPcmcia Cards How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed SequentiallyUse the Feed or Restart key to select a desired option Character Code SelectionAfter selecting a character code, press the Pause key Character Zero SelectionAfter selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause keyFlow Control Code Selection Stop Bit SelectionParity Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionAfter selecting the solenoid type, press the Pause key Control Code Selection After selecting the Strip Wait Status, press the Pause key Strip Wait Status SelectionFeed Key Function Selection After selecting the Feed key function, press the Pause keyAfter selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause keyAfter selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Expansion I/O Interface Type Selection Ribbon Near End SelectionAfter selecting a Plug & Play, press the Pause key Centronics Interface SelectionPlug & Play Selection After selecting the Pre-strip function, press the Pause key Label End/Ribbon End SelectionPre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection After selecting a print head type, press the Pause key System Mode Password SettingPrint Head Type Selection After selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Feed Amount Fine Adjustment Position and Print Tone Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingSelect the sensor to be adjusted by using the Feed key Manually setFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModePress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyMedia has run out Load new media. Then press Error Messages Problems/Cause SolutionsMedia is slack Take up any slack in the media Ribbon has run out Load a new ribbon. Then pressRibbon is not loaded properly Load the ribbon properly Possible ProblemsPossible Problems Causes Solutions ⇒Section Cutter blade is dirty Clean the cutter bladeRefer to .1 Media Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications SX4T-GS20-QM-R Media Supply SpecificationsMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Ribbon type Description Care/Handling of Media and RibbonCombination of Media and Ribbon Media type Vellum paper and labelAppendix 1 Messages and Leds Symbols in the messageWrong password was entered Printer is waiting for a password to Be enteredBase LAN Board is being Initialized Printer did not succeed in writingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard LAN cable Physical Layer100BASE-TX UTP category Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-U1-EU RFID-U1-USRFID-H1-QM SX704-RFID-U2-US-RAt least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper See Black mark sensorMedia and ribbon See Feed gap sensor3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E
Top Page Image Contents