Toshiba B-SX4T owner manual Feed and Pause keys

Page 79

2.PRINTER SETUP

ENGLISH VERSION EO1-33058

2.13 Threshold Setting

2.13Threshold Setting (Cont.)

<5>SENSOR ADJ.

[PAUSE]

<5>SENSOR ADJ. [H]28°C [A]28°C

[PAUSE]

<5>SENSOR ADJ. [REFLECT] 3.5V

[FEED] or [RESTART]

<5>SENSOR ADJ. [REFLECT] 4.8V*

[PAUSE]

<5>SENSOR ADJ. [TRANS.] 2.4V

[FEED] or [RESTART]

<5>SENSOR ADJ. [TRANS.] 4.1V*

[PAUSE]

<5>SENSOR ADJ. [PE]R0.1V T4.8V

[FEED] or [RESTART]

<5>SENSOR ADJ. [PE]R0.1V T4.8V*

[PAUSE]

<5>SENSOR ADJ. [RIBBON] 3.1V

[FEED] or [RESTART]

<5>SENSOR ADJ. [RIBBON] 3.1V*

[PAUSE]

Manual threshold setting procedure

If a paper jam error still occurs even after an automatic threshold setting has been performed, manually set the threshold voltage.

To make a threshold value manually set in this section effective, select the Transmissive Sensor (when using manual threshold value) or Reflective Sensor (when using manual threshold value) within software commands or the printer driver.

1.While holding down the [FEED] and [PAUSE] keys, turn on the printer.

2.When “<1>DIAG.” appears on the LCD Message Display, release the

[FEED] and [PAUSE] keys.

<1>DIAG.

Now, the printer is in the System Mode for system administrators.

3.Press the [FEED] or [RESTART] key until “<5>SENSOR ADJ.” appears on the LCD Message Display.

<5>SENSOR ADJ.

4.Press the [PAUSE] key to enter the Sensor Adjustment Mode.

<5>SENSOR ADJ. [H]28°C [A]28°C

The Sensor Adjustment Mode contains sub menus for displaying the current status of each sensor and for storing “media level” voltage and “no media level” voltage. Each time the [PAUSE] key is pressed, the sub menus are displayed sequentially.

(1)Sensor Status Display:

Temperatures being detected by the Print Head Thermistor and the Ambient Thermistor are displayed.

(2)Black Mark Sensor Status Display:

Voltage being detected by the Black Mark Sensor is displayed.

(3)Black Mark Sensor Adjustment:

Using the media actually used, a “media level” voltage is stored.

(4)Feed Gap Sensor Status Display:

Voltage being detected by the Feed Gap Sensor is displayed.

(5)Feed Gap Sensor Adjustment:

Using the media actually used, a “media level” voltage is stored.

(6)Black Mark Sensor/Feed Gap Sensor Status Display (No media):

“No media level” voltage detected by the Black Mark Sensor/Feed Gap Sensor is displayed.

(7)Black Mark Sensor/Feed Gap Sensor Adjustment (No media):

“No media level” voltage is stored.

(8)Ribbon End Sensor Status Display:

Voltage being detected by the Ribbon End Sensor is displayed.

(9)Ribbon End Sensor Adjustment:

Using the ribbon actually used, a “ribbon level” voltage is stored.

E2-65

Image 79
Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction Features UnpackingQuality Control Report 1 sheet AccessoriesNo FM1647000 Doc. No. EO2-33021Following chapters DimensionsFront View Rear ViewInterior Operation PanelOption Name Type Description OptionsReference Printer SetupSetup Flow ProcedureInstallation Fitting the Fan Filter Connecting the Power CordExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Black Mark Sensor position Setting the Feed Gap Sensor positionRemove the Locking Screw that secures the Media Sensor Strip mode Option Batch modeSTANDARD/PEEL OFF position Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterPcmcia Cards Paragraphs outline how to insert Pcmcia cardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedCharacter Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionParity Selection Stop Bit SelectionFlow Control Code Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionFeed key Head Up Cut/Rewinder SelectionAfter selecting the solenoid type, press the Pause key Solenoid Type SelectionRibbon Saving Function Selection Control Code Selection After selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionInput Prime Selection Web Printer Function SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Ribbon Near End SelectionPlug & Play Selection Centronics Interface SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Label End/Ribbon End SelectionAfter selecting the Pre-strip function, press the Pause key Reverse Feed Speed Selection Maxi Code Specification SelectionAfter selecting the Back Feed Speed, press the Pause key Print Head Type Selection System Mode Password SettingAfter selecting a print head type, press the Pause key After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodReceive Buffer Size Data in the receive buffer is printed as followsRequired Label Length When the Pause key is pressed, Basic program is executed Introduction Installing the Printer DriversGeneral Description Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentPosition and Print When setting +0.0 mmTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Storing a No Media Level Voltage „ Manual Threshold SettingPress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModeOperation ResetPress and hold the Restart key for 3 seconds or longer Cleaning MaintenancePrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsRibbon has run out Load a new ribbon. Then press Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Media is slack Take up any slack in the mediaPossible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Refer to .1 Media Cutter blade is dirty Clean the cutter blade⇒Section Removing Jammed Media This section describes the printer specifications Printer SpecificationsModel SX4T-GS20-QM-R Label Supply SpecificationsMedia Media TypeLabel Detection Area of the Transmissive SensorTag paper with square holes Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Rfid Tags„ B-9704-RFID-H1-QM-R Media feed direction Recommended Media and Ribbon Types RibbonMedia type Description Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messageInitialized Printer did not succeed in writing Printer is waiting for a password to Be enteredWrong password was entered Base LAN Board is beingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard Cable length Segment length Max m Physical LayerLAN cable 100BASE-TX UTP categoryExpansion I/O Interface Option B-7704-IO- QM-R SX704-RFID-U2-US-R RFID-U1-USRFID-U1-EU RFID-H1-QMWhen purchasing the power cord Appendix 3 Power CordAt least, 125% of the rated current of the product Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries See Feed gap sensor See Black mark sensorDevice used to remove labels from the backing paper Media and ribbon3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E