Toshiba B-SX4T Operation, Reset, Press and hold the Restart key for 3 seconds or longer

Page 84

3. ON LINE MODE

ENGLISH VERSION EO1-33058

3.2 Operation

3.2 Operation

NOTE:

For the meaning of error messages and actions to be taken, refer to

Section 5 TROUBLESHOOTING and APPENDIX 1.

When the printer is turned on, the “ON LINE” message appears on the LCD Message Display. It is shown during standby or normal printing.

1.The printer is turned on, standing by, or printing.

ON LINE

B-SX4T V1.0A

2.If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right side shows the remaining number of media to be printed.)

NO PAPER	125
B-SX4T	V1.0A

3.To clear the error, press the [RESTART] key. The printer resumes printing.

ON LINE

B-SX4T V1.0A

4. If the [PAUSE] key is pressed during printing, the printer stops printing temporarily. (The number on the right side shows the remaining number of media to be printed.)

PAUSE 52

B-SX4T V1.0A

5.When the [RESTART] key is pressed, the printer resumes printing.

ON LINE

B-SX4T V1.0A

3.3 Reset

NOTE:

If the [RESTART] key is held for less than 3 seconds when the printer is in an error or pause state, the printer restarts printing. However, when a communication error or command error occurs, the printer returns to an idle condition.

A reset operation clears the print data sent from the computer to the printer, and returns the printer to an idle condition.

1.The printer is turned on, standing by, or printing.

ON LINE

B-SX4T V1.0A

2.To stop printing, or clear the data sent from the computer, press the [PAUSE] key. The printer stops printing.

PAUSE 52

B-SX4T V1.0A

3.Press and hold the [RESTART] key for 3 seconds or longer.

<1>RESET

4.Press the [PAUSE] key. The data sent from the computer will be cleared, and the printer returns to an idle condition.

ON LINE

B-SX4T V1.0A

E3- 2

Image 84

Contents SX4T Series CE Compliance for EU only VorsichtSX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Introduction Features Unpacking Product OverviewAccessories No FM1647000Doc. No. EO2-33021 Quality Control Report 1 sheetDimensions Front ViewRear View Following chaptersOperation Panel InteriorOptions Option Name Type DescriptionPrinter Setup Setup FlowProcedure ReferenceInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionRemove the Locking Screw that secures the Media Sensor Batch mode Strip mode OptionSTANDARD/PEEL OFF position Built-in rewinder mode Option Cut mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterParagraphs outline how to insert Pcmcia cards Pcmcia CardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Parameter Setting While 2PARAMETER SET is displayed on the LCD MessageTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a character code, press the Pause key Character Zero SelectionBaud Rate Selection After selecting a baud rate, press the Pause keyData Length Selection After selecting a data length, press the Pause keyStop Bit Selection Parity SelectionFlow Control Code Selection LCD Language Selection After selecting a language, press the Pause keyAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection After selecting the solenoid type, press the Pause keyRibbon Saving Function Selection Control Code Selection Strip Wait Status Selection After selecting the Strip Wait Status, press the Pause keyFeed Key Function Selection After selecting the Feed key function, press the Pause keyKanji Code Selection After selecting a Kanji code, press the Pause keyEuro Code Selection After selecting a Euro code, press the Pause keyAuto Print Head Check Selection After selecting auto print head check, press the Pause keyCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Pre-Strip SelectionAfter selecting the Pre-strip function, press the Pause key Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key System Mode Password Setting Print Head Type SelectionAfter selecting a print head type, press the Pause key Dump Mode Setting After selecting the receive buffer, press the Pause keyUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Position and Print Tone Fine Adjustment Feed Amount Fine AdjustmentCut/Strip Position Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Jam errorsSelect the sensor to be adjusted by using the Feed key Manually setFeed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Media has run out Load new media. Then pressMedia is slack Take up any slack in the media Ribbon has run out Load a new ribbon. Then pressPossible Problems Possible Problems Causes SolutionsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter blade Refer to .1 Media⇒Section Removing Jammed Media Printer Specifications This section describes the printer specificationsModel SX4T-GS20-QM-R Supply Specifications MediaMedia Type LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Care/Handling of Media and Ribbon Ribbon type DescriptionCombination of Media and Ribbon Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsPrinter is waiting for a password to Be entered Wrong password was enteredBase LAN Board is being Initialized Printer did not succeed in writingFollowing message appears Appendix 2 Interface Parallel interface Centronics StandardConnector PINSerial interface Standard Physical Layer LAN cable100BASE-TX UTP category Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-U1-US RFID-U1-EURFID-H1-QM SX704-RFID-U2-US-RAppendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries See Black mark sensor Device used to remove labels from the backing paperMedia and ribbon See Feed gap sensorIndex 3-1, A1-1Index Waste Recycling information for users EO1-33058E