Toshiba B-SX4T owner manual On Line Mode, Operation Panel

Page 83

3. ON LINE MODE

ENGLISH VERSION EO1-33058

3.1 Operation Panel

3. ON LINE MODE

3.1 Operation Panel

This chapter describes usage of the keys on the Operation Panel in On Line mode.

When the printer is in On Line mode and connected to a host computer, the normal operation of printing images on labels or tags can be accomplished.

•The figure below illustrates the operation panel and key functions.

LCD Message Display

ON LINE LED (Green)

	POWER LED	ERROR LED (Red)
	(Green)	ERROR LED (Red)
	(Green)
	[FEED] key
	[RESTART] key	[PAUSE] key
	[RESTART] key

NOTE:

Flashes only when the Ribbon Near End Detection function is selected.

NOTE:

Use the [RESTART] key to resume printing after a pause, or after clearing an error.

The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the printer’s current status. Up to 32 characters can be displayed on two lines.

There are three LED lights on the operation panel.

LED	Illuminates when…		Flashes when…
POWER	The printer is turned on.	-----
ON LINE	The printer is ready to		The printer is
	print.		communicating with
			your computer.
ERROR	Any error occurs with		The ribbon is nearly
	the printer.		over. (See NOTE.)

There are three keys on the operation panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed the media.

E3- 1

Image 83

Contents SX4T Series Vorsicht CE Compliance for EU onlySX4T Series Waste Recycling information for users For all countries and areas Meanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction Features UnpackingQuality Control Report 1 sheet AccessoriesNo FM1647000 Doc. No. EO2-33021Following chapters DimensionsFront View Rear ViewInterior Operation PanelOption Name Type Description OptionsReference Printer SetupSetup Flow ProcedureInstallation Example of US Type Connecting the Power CordFitting the Fan Filter Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Remove the Locking Screw that secures the Media Sensor Setting the Feed Gap Sensor positionSetting the Black Mark Sensor position STANDARD/PEEL OFF position Batch modeStrip mode Option Cut mode Option Built-in rewinder mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning on the Printer Turning the PrinterFollowing Pcmcia cards or equivalent can be used Paragraphs outline how to insert Pcmcia cardsPcmcia Cards How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedCharacter Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionFlow Control Code Selection Stop Bit SelectionParity Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionFeed key Head Up Cut/Rewinder SelectionRibbon Saving Function Selection Solenoid Type SelectionAfter selecting the solenoid type, press the Pause key Control Code Selection After selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Expansion I/O Interface Type Selection Ribbon Near End SelectionAfter selecting a Plug & Play, press the Pause key Centronics Interface SelectionPlug & Play Selection After selecting the Pre-strip function, press the Pause key Label End/Ribbon End SelectionPre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection After selecting a print head type, press the Pause key System Mode Password SettingPrint Head Type Selection After selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed General Description Installing the Printer DriversIntroduction Parallel Interface Installing the Printer DriverWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using a Strip Module or an optional Cutter Module Coordinate Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Cut/Strip Position Fine AdjustmentTone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Select the sensor to be adjusted by using the Feed keyFeed and Pause keys „ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V Operation Panel On Line ModePress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Covers and Panels Optional Cutter Module Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsRibbon has run out Load a new ribbon. Then press Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Media is slack Take up any slack in the mediaRibbon is not loaded properly Load the ribbon properly Possible ProblemsPossible Problems Causes Solutions ⇒Section Cutter blade is dirty Clean the cutter bladeRefer to .1 Media Removing Jammed Media Model Printer SpecificationsThis section describes the printer specifications SX4T-GS20-QM-R Label Supply SpecificationsMedia Media TypeTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective Sensor„ B-9704-RFID-H1-QM-R Rfid Tags„ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R Media feed direction Media type Description RibbonRecommended Media and Ribbon Types Media type Vellum paper and label Care/Handling of Media and RibbonRibbon type Description Combination of Media and RibbonAppendix 1 Messages and Leds Symbols in the messageInitialized Printer did not succeed in writing Printer is waiting for a password to Be enteredWrong password was entered Base LAN Board is beingFollowing message appears Parallel interface Centronics Standard Appendix 2 InterfacePIN ConnectorSerial interface Standard Cable length Segment length Max m Physical LayerLAN cable 100BASE-TX UTP categoryExpansion I/O Interface Option B-7704-IO- QM-R SX704-RFID-U2-US-R RFID-U1-USRFID-U1-EU RFID-H1-QMAt least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries See Feed gap sensor See Black mark sensorDevice used to remove labels from the backing paper Media and ribbon3-1, A1-1 IndexIndex Waste Recycling information for users EO1-33058E