Toshiba B-SX4T owner manual Printer Driver Upgrades, Others

Page 66

2. PRINTER SETUP

ENGLISH VERSION EO1-33058

2.10 Installing the Printer Drivers

2.10.6 Cautions

(1)Printer Driver Upgrades

•To upgrade the printer driver to this version, uninstall the previous version of the printer driver, before installing this printer driver.

•Be sure to restart your host computer, after you upgrade the printer driver.

•When your operating system is Windows 98, or Windows Me, be sure to restart your host computer, after you uninstall the previous version of the printer driver. Or, the printer driver is not upgraded properly.

(2)Others

•If your operating system is Windows 2000 or Windows XP, when plug-and-play printer installation in progress is stopped, be sure to delete the printer detected and displayed on the “Device Manager” tab of the “System Properties” dialog box.

•Before uninstalling the printer driver, be sure to complete all of printing, the status monitor, and properties settings.

•Before deleting a port, be sure to check if other printers also use it. If there are printers which use the port to be deleted, change their port to another, before deleting the port.

E2-52

Image 66

Contents SX4T Series CE Compliance for EU only VorsichtSX4T Series Waste Recycling information for users For all countries and areas Safety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Unpacking Product OverviewDoc. No. EO2-33021 AccessoriesNo FM1647000 Quality Control Report 1 sheetRear View DimensionsFront View Following chaptersOperation Panel InteriorOptions Option Name Type DescriptionProcedure Printer SetupSetup Flow ReferenceInstallation Connecting the Power Cord Fitting the Fan FilterExample of US Type Loading the Media Do not over-tighten the Locking Ring of the Supply Holder Setting the Feed Gap Sensor position Setting the Black Mark Sensor positionRemove the Locking Screw that secures the Media Sensor Batch mode Strip mode OptionSTANDARD/PEEL OFF position Built-in rewinder mode Option Cut mode OptionLoading the Ribbon Auto Ribbon Saving Mode Connecting the Cables to Your Printer Turning the Printer Turning on the PrinterParagraphs outline how to insert Pcmcia cards Pcmcia CardsFollowing Pcmcia cards or equivalent can be used How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message SequentiallyAfter selecting a character code, press the Pause key Character Code SelectionUse the Feed or Restart key to select a desired option Character Zero SelectionData Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause keyStop Bit Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause keyHead Up Cut/Rewinder Selection Feed keySolenoid Type Selection After selecting the solenoid type, press the Pause keyRibbon Saving Function Selection Control Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause keyEuro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause keyCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type SelectionCentronics Interface Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon End Selection Pre-Strip SelectionAfter selecting the Pre-strip function, press the Pause key Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key System Mode Password Setting Print Head Type SelectionAfter selecting a print head type, press the Pause key Use the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Installing the Printer Drivers IntroductionGeneral Description Installing the Printer Driver Parallel InterfaceWindows 98/Me E2-38 Windows 2000/XP E2-40 USB Interface E2-42 E2-43 E2-44 Finish button E2-46 E2-47 E2-48 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using a Strip Module or an optional Cutter Module Cut/Strip Position Fine Adjustment Position and Print Tone Fine AdjustmentFeed Amount Fine Adjustment Coordinate Fine AdjustmentWhen setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Select the sensor to be adjusted by using the Feed key Threshold SettingJam errors Manually setFeed and Pause keys „ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds THRESHOLDR4.0V THRESHOLDT4.0V THRESHOLDR3.9V On Line Mode Operation PanelReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Covers and Panels Optional Cutter Module Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyMedia is slack Take up any slack in the media Error Messages Problems/Cause SolutionsMedia has run out Load new media. Then press Ribbon has run out Load a new ribbon. Then pressPossible Problems Possible Problems Causes SolutionsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter blade Refer to .1 Media⇒Section Removing Jammed Media Printer Specifications This section describes the printer specificationsModel SX4T-GS20-QM-R Media Type Supply SpecificationsMedia LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRfid Tags „ B-9704-RFID-U1-US-R and B-9704-RFID-U1-EU-R„ B-9704-RFID-H1-QM-R Media feed direction Ribbon Recommended Media and Ribbon TypesMedia type Description Combination of Media and Ribbon Care/Handling of Media and RibbonRibbon type Description Media type Vellum paper and labelSymbols in the message Appendix 1 Messages and LedsBase LAN Board is being Printer is waiting for a password to Be enteredWrong password was entered Initialized Printer did not succeed in writingFollowing message appears Appendix 2 Interface Parallel interface Centronics StandardConnector PINSerial interface Standard 100BASE-TX UTP category Physical LayerLAN cable Cable length Segment length Max mExpansion I/O Interface Option B-7704-IO- QM-R RFID-H1-QM RFID-U1-USRFID-U1-EU SX704-RFID-U2-US-RAppendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Media and ribbon See Black mark sensorDevice used to remove labels from the backing paper See Feed gap sensorIndex 3-1, A1-1Index Waste Recycling information for users EO1-33058E