Issue 10/06 | 6 Commissioning |
P0304 =... 
P0304 =...
P0305 =... 
P0305 =...
P0307 =... 
P0307 =...
P0308 =... 
P0308 =...
P0309 =... 
P0309 =... 
P0310 =...
P0311 =...
P0320 = ...
P0335 =...
P0640 =...
P0700 =...
Rated motor voltage |
|
|
|
|
|
|
|
|
|
|
|
| ||
(Nominal motor voltage [V] |
|
|
|
|
|
|
|
|
|
|
|
|
| |
from rating plate) |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The rated motor voltage on the rating |
|
|
|
|
|
|
|
|
|
|
|
| ||
plate must be checked, regarding the |
|
|
|
|
|
|
|
|
|
|
|
| ||
star/delta circuit configuration to |
|
|
|
|
|
|
|
|
|
|
| |||
|
| P0310 |
| P0304 |
|
|
|
| ||||||
ensure that it matches with the circuit |
|
|
|
|
|
|
|
|
|
|
|
| ||
connection configured at the motor |
|
|
|
|
|
|
|
|
|
|
|
| ||
terminal board |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Rated motor current |
|
|
|
|
|
|
|
|
|
|
|
| ||
(Nominal motor current [A] |
|
|
|
|
|
|
|
|
|
|
|
|
| |
from rating plate) |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||
Rated motor power |
|
| P0307 | P0305 |
|
|
|
| ||||||
|
|
| P0308 |
| P0311 |
|
|
| ||||||
(Nominal motor power [kW/hp] |
|
|
|
|
|
|
| |||||||
Example of a typical motor rating plate | ||||||||||||||
from rating plate) |
| |||||||||||||
| (data for a delta circuit configuration). | |||||||||||||
If P0100 = 0 or 2, value will be in kW. | ||||||||||||||
If P0100 = 1, value will be in in hp. |
|
|
|
|
|
|
|
|
|
|
|
| ||
Rated motor cosPhi |
|
|
|
|
|
|
|
|
|
|
| |||
(Nominal motor power factor (cos ϕ) from rating plate) If the setting is 0, the value is automatically calculated P0100 = 1,2: P0308 no significance, no entry required.
Rated motor efficiency | |
(Nominal motor efficiency in [%] from rating plate) |
|
Setting 0 causes internal calculation of value. |
|
P0100 = 0: P0309 no significance, no entry required. |
|
|
|
Rated motor frequency | 50.00 Hz |
(Nominal motor frequency in [Hz] from rating plate) |
|
Pole pair number recalculated automatically if parameter is changed. |
|
|
|
Rated motor speed | |
(Nominal motor speed in [rpm] from rating plate) |
|
Setting 0 causes internal calculation of value. |
|
NOTE
An entry must be made for
Motor magnetizing current | 0.0 |
(this is entered as a % referred to P0305)
Motor magnetizing current as a % relative to P0305 (rated motor current).
With P0320 = 0, the motor magnetizing current is calculated using P0340 = 1 or using P3900 = 1 - 3 (end of the quick commissioning) – and is displayed in parameter r0331.
Motor cooling | 0 | |
(Selects motor cooling system used) |
| |
0 |
| |
1 |
| |
2 |
| |
3 |
| |
Motor overload factor | 150 % | |
(Motor overload factor in [%] relative to P0305)
This defines the limit of the maximum output current as a % of the rated motor current (P0305). This parameter is set, using P0205 for constant torque, to 150 %, and for variable torque, to 110 %.
Selection of command source | 2 |
(enters the command source)
0Factory default setting
1BOP (keypad)
2Terminal
4USS on BOP link
5USS on COM link (control terminals 29 and 30)
6CB on COM link (CB = communications module)
MICROMASTER 440 | 29 |
Operating Instructions (Compact) |