Yamaha YSP-900 owner manual Installation, Before installing this unit, Installing this unit, 11 En

Page 13

INSTALLATION

This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.

Before installing this unit

This unit creates surround sound by reflecting projected sound beams off the walls of your listening room. The surround sound effects produced by this unit may not be sufficient when the unit is installed in the following locations.

Rooms with surfaces inadequate for reflecting sound beams

Rooms with acoustically absorbent surfaces

Rooms with measurements outside the following range W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)

Rooms with less than 1.8 m from the listening position to the speaker positions

Rooms where objects such as furniture are likely to obstruct the path of sound beams

Rooms where the listening position is close to the walls

Rooms where the listening position is not in front of

this unit

Make sure you leave an adequate amount of ventilation space so that heat can escape. Make at least 5 cm of space above or below this unit.

Side view

5 cm or more

FrontRear

Notes

We do not recommend installing this unit so that it is positioned directly on the floor of your listening room. Please install this unit using a metal wall bracket, rack or stand.

This unit weighs 9.0 kg. Be sure to install this unit where it will not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.

When using a cathode-ray tube (CRT) TV, do not install this unit directly above your TV.

This unit is shielded against magnetic rays. However, if the picture on your TV screen becomes blurred or distorted, we recommend moving the speakers away from your TV.

Installing this unit

Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.

Parallel installation

Install this unit in the exact center of the wall when it is measured from the left and right corners.

An object, such as furniture

Corner installation

Install this unit in the corner at a 40º to 50º angle from the adjacent walls.

40° to 50°

An object, such as furniture

PREPARATION

English

11 En

Image 13
Contents YSP-900 For U.K. Customers Contents Overview Features Using this Manual Remote control ⋅1 Supplied AccessoriesYellow Optimizer microphone ⋅1 Orange Audio pin cable ⋅1 Front panel Controls and FunctionsInput STANDBY/ONFront panel display VCR TV/STB Subwoofer Video AUX Rear panelOUT Remote control 10 En Before installing this unit InstallationInstalling this unit 11 En12 En Installation examplesExample Using a stand Using a metal wall bracketUsing a rack 13 En14 En ConnectionsAudio connection Video connection DVD player Subwoofer15 En Connecting a TVDigital and analog audio connections Video connections Cables used for connections16 En Connecting a DVD player/recorder17 En Connecting a VCRDVD Audio Input Optical Coaxial18 En Connecting a digital satellite tuner or a cable TV tunerOutput Rear panel of this unit 19 En Connecting other external components20 En Connecting a subwoofer21 En Connecting the power supply cableTo the AC outlet Operation range of the remote control Installing batteries in the remote controlClose the battery cover Getting StartedOperational buttons only when YSP is Selected Using the remote control Turning on the powerFront panel Remote control 23 EnDisplaying the OSD Using SET Menu24 En Front panel25 En Flow chart of SET MenuPress Menu on the remote control Language SetupPress / to select Language Setup and then press Enter Changing OSD Language27 En Flow chart of Auto SetupBeam optimization Sound optimization 28 En Installing the optimizer microphone29 En Using Auto Setup IntelliBeamAssembling the supplied cardboard Microphone stand Center line30 En Auto SetupBEAM+SOUND Optimz 31 En32 En Show ResultExample Before the Auto Setup procedure starts Error messages for Auto SetupWhile the Auto Setup procedure is in progress 33 EnSaving settings Using the System MemoryConvenient usage of the system memory 34 EnSET Menu Loading settings35 En Press Enter againPress / to select Load and then press 36 EnPlayback Remote control operationsSelecting the input source 37 En38 En Playing back sourcesPress Mute on the remote control to mute the sound Adjusting the volumeMuting the sound 39 EnEnjoying Surround Sound Press 5BEAM on the remote control to select the 5 beamBeam 40 EnStereo plus 3 beam Beam Press 3BEAM on the remote control to select the 3 beam41 En Status Indicator Decoder indicators42 En Surround modes and recommended sourcesSurround sound Enjoying 2-channel sources43 En 44 En Press TV on the remote controlSelect the TV channel you want to watch When Dolby Pro Logic II Music is selected Adjusting surround mode parametersWhen DTS Neo6 Music is selected 45 EnStereo playback Enjoying Stereo Sound46 En 47 En Using auto-adjust functionMy beam microphone Press MY Beam on the remote control Using manual-adjust functionPress / while MY Beam is displayed to adjust the angle 48 EnWhat is a sound field? Using Sound Field Programs49 En Elements of a sound fieldMusic program 50 EnMovie program Sports program51 En Press / on the remote control52 En Using the Volume ModeEffect.LvlMIN Effect.LvlMID Effect.LvlMAX 53 En54 En Press on the remote control55 En Using the Sleep Timer56 En Canceling the sleep timerDisappears 57 En Manual SetupManual Setup Using Manual Setup58 En Setting parameters Asetting Parameters 1/3Installed Position Installed position of this unit 2BEAM MenuBeam Adjustment Beam adjustment Bbeam Adjustment60 En Horizontal Angle Horizontal angleBeam Travel Length Beam travel length 61 EnFocal Length Focal length Front left channel62 En Cimage LocationImage Location Image location 63 En 1SOUND MenuTone Control Tone control Subwoofer SET Subwoofer setCmute Level Daudio DelayEroom EQ 64 EnInput Menu Binput ModeCinput Trim 65 EnInput Rename Input rename 66 EnPress / to select the desired character Adimmer SET Display MenuBosd SET Cunit SETUsing the test tone Adjusting the Audio BalancePress / to select the channel you want to adjust 68 EnPress Test when you have completed all your adjustments Using the audio output being played back69 En 70 En 71 En Selecting the Input ModeAuto DTSUsing the system parameters Adjusting System ParametersSetting the Memory Protect 72 EnPress / to switch between Protect on Protect OFF Setting the MAX VolumePress / to adjust the maximum volume level 73 EnSetting the Demo Mode Setting the Turn on VolumePress / to adjust the initial volume level 74 EnPress / to switch between Demo on Demo OFF Setting the Factory Preset75 En 76 En Press / to switch between Preset Reset and Preset CancelSetting remote control codes Remote Control Features77 En Code SET78 En Controlling other componentsOperating your TV Operating your DVD player79 En Set the operation mode selector to TV/AVOperating your VCR Operating your STB CATV/Satellite tunerSetting macros for the TV with the tuning capability Using the TV macro80 En Canceling the macros Setting macros for the TV without the tuning capability81 En Operating macros82 En TroubleshootingGeneral 83 En 84 En Remote controlAudio formats GlossaryAudio information 85 En86 En Index87 En SpecificationsAMP Section Speaker SectionDVD Player VCRSatellite Tuner Cable TV TunerWH83000-1 On the upper shelf to keep it away from the floor Cables used for connectionsEnjoying surround sound