Yamaha YSP-900 owner manual Playing back sources, 38 En

Page 40

PLAYBACK

Set the operation mode selector to YSP to switch to the operation mode of this unit and then press VCR on the remote control to play back a video tape.

TV/AV

VCR

YSP

 

VOL

Set the operation mode selector to YSP to switch to the operation mode of this unit and then press AUX on the remote control to play back a component connected to the AUX jack on the rear panel of this unit.

TV/AV

AUX

YSP

 

VOL

Playing back sources

Once an input source is selected (see page 37), you can play back the selected input source.

Note

This section uses a DVD player as an example of the playback source.

y

For details on the TV and the DVD player you are using, refer to the owner’s manual supplied with the TV and the DVD player.

1Turn on the power of your DVD player using the remote control supplied with the DVD player.

2Switch to the video input on your TV using the remote control supplied with the TV so that the DVD menu screen is displayed.

3If necessary, turn down the volume of your TV until you cannot hear any sound.

4Set the operation mode selector to YSP to switch to the operation mode of this unit.

TV/AV

YSP

5Press DVD on the remote control to select DVD as the input source.

DVD

6Play back the DVD on your DVD player using the supplied remote control.

Audio signals from your DVD player are output from this unit.

y

You can check the digital signal being input at the DVD player with the digital connection (optical/coaxial). Press ST+3BEAM on the remote control while playing back a DVD recorded in 5.1

channel. The DIGITAL or indicator lights up when this unit detects the 5.1 channel signal input at the optical/

coaxial jack. If the PCM indicator lights up, confirm the settings of the digital output, bitstream output, and/or DTS output of the DVD player.

If the output volume is too low, increase the volume on this unit to around 45.

If you have set the appropriate remote control codes for your TV and DVD player, you can use the remote control supplied with this unit to operate these components. For details on how to set remote control codes, see page 77.

38 En

Image 40
Contents YSP-900 For U.K. Customers Contents Overview Features Using this Manual Remote control ⋅1 Supplied AccessoriesYellow Optimizer microphone ⋅1 Orange Audio pin cable ⋅1 Controls and Functions Front panelInput STANDBY/ONFront panel display VCR TV/STB Subwoofer Video AUX Rear panelOUT Remote control 10 En Installation Before installing this unitInstalling this unit 11 En12 En Installation examplesExample Using a metal wall bracket Using a standUsing a rack 13 EnConnections 14 EnAudio connection Video connection DVD player SubwooferConnecting a TV 15 EnDigital and analog audio connections Video connections Cables used for connectionsConnecting a DVD player/recorder 16 EnConnecting a VCR 17 EnDVD Audio Input Optical Coaxial18 En Connecting a digital satellite tuner or a cable TV tunerOutput Rear panel of this unit Connecting other external components 19 EnConnecting a subwoofer 20 En21 En Connecting the power supply cableTo the AC outlet Installing batteries in the remote control Operation range of the remote controlClose the battery cover Getting StartedUsing the remote control Turning on the power Operational buttons only when YSP is SelectedFront panel Remote control 23 EnUsing SET Menu Displaying the OSD24 En Front panelFlow chart of SET Menu 25 EnLanguage Setup Press Menu on the remote controlPress / to select Language Setup and then press Enter Changing OSD Language27 En Flow chart of Auto SetupBeam optimization Sound optimization Installing the optimizer microphone 28 EnUsing Auto Setup IntelliBeam 29 EnAssembling the supplied cardboard Microphone stand Center lineAuto Setup 30 En31 En BEAM+SOUND Optimz32 En Show ResultExample Error messages for Auto Setup Before the Auto Setup procedure startsWhile the Auto Setup procedure is in progress 33 EnUsing the System Memory Saving settingsConvenient usage of the system memory 34 EnLoading settings SET Menu35 En Press Enter again36 En Press / to select Load and then pressRemote control operations PlaybackSelecting the input source 37 EnPlaying back sources 38 EnAdjusting the volume Press Mute on the remote control to mute the soundMuting the sound 39 EnPress 5BEAM on the remote control to select the 5 beam Enjoying Surround SoundBeam 40 EnStereo plus 3 beam Beam Press 3BEAM on the remote control to select the 3 beam41 En Decoder indicators Status Indicator42 En Surround modes and recommended sourcesSurround sound Enjoying 2-channel sources43 En 44 En Press TV on the remote controlSelect the TV channel you want to watch Adjusting surround mode parameters When Dolby Pro Logic II Music is selectedWhen DTS Neo6 Music is selected 45 EnStereo playback Enjoying Stereo Sound46 En 47 En Using auto-adjust functionMy beam microphone Using manual-adjust function Press MY Beam on the remote controlPress / while MY Beam is displayed to adjust the angle 48 EnUsing Sound Field Programs What is a sound field?49 En Elements of a sound field50 En Music programMovie program Sports programPress / on the remote control 51 EnUsing the Volume Mode 52 En53 En Effect.LvlMIN Effect.LvlMID Effect.LvlMAXPress on the remote control 54 EnUsing the Sleep Timer 55 En56 En Canceling the sleep timerDisappears Manual Setup 57 EnManual Setup Using Manual Setup58 En Asetting Parameters 1/3 Setting parametersInstalled Position Installed position of this unit 2BEAM MenuBbeam Adjustment Beam Adjustment Beam adjustment60 En Horizontal Angle Horizontal angle61 En Beam Travel Length Beam travel lengthFocal Length Focal length Front left channel62 En Cimage LocationImage Location Image location 1SOUND Menu 63 EnTone Control Tone control Subwoofer SET Subwoofer setDaudio Delay Cmute LevelEroom EQ 64 EnBinput Mode Input MenuCinput Trim 65 EnInput Rename Input rename 66 EnPress / to select the desired character Display Menu Adimmer SETBosd SET Cunit SETAdjusting the Audio Balance Using the test tonePress / to select the channel you want to adjust 68 EnPress Test when you have completed all your adjustments Using the audio output being played back69 En 70 En Selecting the Input Mode 71 EnAuto DTSAdjusting System Parameters Using the system parametersSetting the Memory Protect 72 EnSetting the MAX Volume Press / to switch between Protect on Protect OFFPress / to adjust the maximum volume level 73 EnSetting the Turn on Volume Setting the Demo ModePress / to adjust the initial volume level 74 EnPress / to switch between Demo on Demo OFF Setting the Factory Preset75 En Press / to switch between Preset Reset and Preset Cancel 76 EnRemote Control Features Setting remote control codes77 En Code SETControlling other components 78 EnOperating your TV Operating your DVD playerSet the operation mode selector to TV/AV 79 EnOperating your VCR Operating your STB CATV/Satellite tunerSetting macros for the TV with the tuning capability Using the TV macro80 En Setting macros for the TV without the tuning capability Canceling the macros81 En Operating macros82 En TroubleshootingGeneral 83 En Remote control 84 EnGlossary Audio formatsAudio information 85 EnIndex 86 EnSpecifications 87 EnAMP Section Speaker SectionVCR DVD PlayerCable TV Tuner Satellite TunerWH83000-1 Cables used for connections On the upper shelf to keep it away from the floorEnjoying surround sound