Yamaha YSP-900 owner manual Auto Setup, 30 En

Page 32

AUTO SETUP (IntelliBeam)

Notes

•Make sure that your listening room is as quiet as possible while this unit is performing the AUTO SETUP procedure.

•To achieve the best results possible, evacuate yourself from your listening room until the AUTO SETUP procedure is completed so that you may not obstruct the path of sound beams.

•Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure.

•The AUTO SETUP procedure may not be run successfully if this unit is installed in one of the rooms described in “Before installing this unit” on page 11. In such cases, run MANUAL SETUP (see page 57) to manually adjust the corresponding parameters.

•If an error occurs, an error buzzer is played, the AUTO SETUP procedure stops and then an error message appears on the screen. See “Error messages for AUTO SETUP” on page 33 for appropriate remedies.

y

•The AUTO SETUP procedure takes about 3 minutes maximum. A chime is played when the AUTO SETUP procedure is run successfully.

•If there are curtains in your listening room, we recommend following the procedure below.

1.Open the curtains to improve sound reflection.

2.Run BEAM OPTIMZ only.

3.Close the curtains.

4.Run SOUND OPTIMZ only.

•You can save the settings optimized by the AUTO SETUP procedure (see page 34). A set of settings optimized according to specific conditions of your listening environment can be recalled later depending on the varying conditions of your listening environment (see page 35).

1Press STANDBY/ON on the front panel or on the remote control to turn on the power of this unit.

If a subwoofer is connected to this unit, turn on the power of the subwoofer.

3Press MENU on the remote control.

The SET MENU screen appears on your TV.

 

SET MENU

MENU

. ;MEMORY

 

;AUTO SETUP

 

;MANUAL SETUP

 

;LANGUAGE SETUP

 

[p]/[p]:Up/Down

 

[ENTER]:Enter

y

•The control buttons used for SET MENU are displayed on the bottom of the screen.

•To return to the previous screen while using SET MENU, press RETURN on the remote control.

•To cancel the SET MENU screen, press MENU again.

•You can start the BEAM+SOUND OPTIMZ procedure simply by pressing and holding AUTO SETUP on the remote control for more than 2 seconds. Step 4 and 5 are skipped and then the screen shown in step 5 is displayed on your TV. Start the AUTO SETUP procedure from step 6.

•You can also perform the following operations in the front panel display.

4 Press / on the remote control to select AUTO SETUP and then press ENTER.

The following screen appears on your TV.

ENTER

ENTER

 

or

STANDBY/ON

 

Front panel

Remote control

2Set the operation mode selector to YSP to switch to the operation mode of this unit.

TV/AV

YSP

;AUTO SETUP

. 1)BEAM+SOUND OPTIMZ 2)BEAM OPTIMZ only 3)SOUND OPTIMZ only

[p]/[p]:Up/Down [ENTER]:Enter

30 En

Page 31 Page 33
Image 32
Page 31 Page 33
Contents YSP-900 For U.K. Customers Contents Overview Features Using this Manual Yellow Optimizer microphone ⋅1 Orange Audio pin cable ⋅1 Supplied AccessoriesRemote control ⋅1 Controls and Functions Front panelInput STANDBY/ONFront panel display OUT Rear panelVCR TV/STB Subwoofer Video AUX Remote control 10 En Installation Before installing this unitInstalling this unit 11 EnExample Installation examples12 En Using a metal wall bracket Using a standUsing a rack 13 EnConnections 14 EnAudio connection Video connection DVD player SubwooferConnecting a TV 15 EnDigital and analog audio connections Video connections Cables used for connectionsConnecting a DVD player/recorder 16 EnConnecting a VCR 17 EnDVD Audio Input Optical CoaxialOutput Rear panel of this unit Connecting a digital satellite tuner or a cable TV tuner18 En Connecting other external components 19 EnConnecting a subwoofer 20 EnTo the AC outlet Connecting the power supply cable21 En Installing batteries in the remote control Operation range of the remote controlClose the battery cover Getting StartedUsing the remote control Turning on the power Operational buttons only when YSP is SelectedFront panel Remote control 23 EnUsing SET Menu Displaying the OSD24 En Front panelFlow chart of SET Menu 25 EnLanguage Setup Press Menu on the remote controlPress / to select Language Setup and then press Enter Changing OSD LanguageBeam optimization Sound optimization Flow chart of Auto Setup27 En Installing the optimizer microphone 28 EnUsing Auto Setup IntelliBeam 29 EnAssembling the supplied cardboard Microphone stand Center lineAuto Setup 30 En31 En BEAM+SOUND OptimzExample Show Result32 En Error messages for Auto Setup Before the Auto Setup procedure startsWhile the Auto Setup procedure is in progress 33 EnUsing the System Memory Saving settingsConvenient usage of the system memory 34 EnLoading settings SET Menu35 En Press Enter again36 En Press / to select Load and then pressRemote control operations PlaybackSelecting the input source 37 EnPlaying back sources 38 EnAdjusting the volume Press Mute on the remote control to mute the soundMuting the sound 39 EnPress 5BEAM on the remote control to select the 5 beam Enjoying Surround SoundBeam 40 En41 En Press 3BEAM on the remote control to select the 3 beamStereo plus 3 beam Beam Decoder indicators Status Indicator42 En Surround modes and recommended sources43 En Enjoying 2-channel sourcesSurround sound Select the TV channel you want to watch Press TV on the remote control44 En Adjusting surround mode parameters When Dolby Pro Logic II Music is selectedWhen DTS Neo6 Music is selected 45 En46 En Enjoying Stereo SoundStereo playback My beam microphone Using auto-adjust function47 En Using manual-adjust function Press MY Beam on the remote controlPress / while MY Beam is displayed to adjust the angle 48 EnUsing Sound Field Programs What is a sound field?49 En Elements of a sound field50 En Music programMovie program Sports programPress / on the remote control 51 EnUsing the Volume Mode 52 En53 En Effect.LvlMIN Effect.LvlMID Effect.LvlMAXPress on the remote control 54 EnUsing the Sleep Timer 55 EnDisappears Canceling the sleep timer56 En Manual Setup 57 En58 En Using Manual SetupManual Setup Asetting Parameters 1/3 Setting parametersInstalled Position Installed position of this unit 2BEAM MenuBbeam Adjustment Beam Adjustment Beam adjustment60 En Horizontal Angle Horizontal angle61 En Beam Travel Length Beam travel lengthFocal Length Focal length Front left channelImage Location Image location Cimage Location62 En 1SOUND Menu 63 EnTone Control Tone control Subwoofer SET Subwoofer setDaudio Delay Cmute LevelEroom EQ 64 EnBinput Mode Input MenuCinput Trim 65 EnPress / to select the desired character 66 EnInput Rename Input rename Display Menu Adimmer SETBosd SET Cunit SETAdjusting the Audio Balance Using the test tonePress / to select the channel you want to adjust 68 En69 En Using the audio output being played backPress Test when you have completed all your adjustments 70 En Selecting the Input Mode 71 EnAuto DTSAdjusting System Parameters Using the system parametersSetting the Memory Protect 72 EnSetting the MAX Volume Press / to switch between Protect on Protect OFFPress / to adjust the maximum volume level 73 EnSetting the Turn on Volume Setting the Demo ModePress / to adjust the initial volume level 74 En75 En Setting the Factory PresetPress / to switch between Demo on Demo OFF Press / to switch between Preset Reset and Preset Cancel 76 EnRemote Control Features Setting remote control codes77 En Code SETControlling other components 78 EnOperating your TV Operating your DVD playerSet the operation mode selector to TV/AV 79 EnOperating your VCR Operating your STB CATV/Satellite tuner80 En Using the TV macroSetting macros for the TV with the tuning capability Setting macros for the TV without the tuning capability Canceling the macros81 En Operating macrosGeneral Troubleshooting82 En 83 En Remote control 84 EnGlossary Audio formatsAudio information 85 EnIndex 86 EnSpecifications 87 EnAMP Section Speaker SectionVCR DVD PlayerCable TV Tuner Satellite TunerWH83000-1 Cables used for connections On the upper shelf to keep it away from the floorEnjoying surround sound
Top Page Image Contents