Peerless Industries PRG-UNV-S, PRG-UNV-W manual Installation to Wood Joist Ceilings

Page 5

Installation to Wood Joist Ceilings

WARNING

Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Tighten wood screws so that wall plate is fi rmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud fi nder is highly recommended.

Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated ny UL).

2Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Make sure that the mounting holes are in the center of the wood joist. Drill two 5/32" (4mm) dia. holes to a minimum depth of 2-1/2" (64mm). Attach projector mount assembly (A) with two #14 x 2-1/2" (6mm x 64mm) wood screws (D) and two fl at washers (F) as shown in fi gure 2.1 or fi gure 2.2 depending on joist orientation.

Tighten wood screws (D) using 3/8" (10mm) socket wrench or phillips screwdriver until projector mount assembly (A) is fi rmly attached.

Skip to step 5.

WOOD JOIST

fig. 2.1

A

F

ACCESS SLOT FOR

OPEN END WRENCH

ALLOWS TIGHTENING

OF WOOD SCREW (D).

ACCESS SLOT FOR

OPEN END WRENCH

ALLOWS TIGHTENING

OF WOOD SCREW (D).

WOOD JOIST

fig. 2.2

D

A

F

D

5 of 51

ISSUED: 09-30-09 SHEET #: 056-9024-5 07-18-11

Image 5
Contents Max UL Load Capacity FeaturesTable of Contents Tools Needed for AssemblyPRG-UNV PRG-UNV-S PRG-UNV-W Parts ListSkip to step Installation to Extension Column/Ceiling PlateInstallation to Wood Joist Ceilings Installation to Concrete Ceilings View Not evaluated by UL Professional installation only Installation to Threaded RodAttaching Adapter Plate to Projector L or M Connection Block Cable Management Mount assembly to full upward tilt positionProjector Alignment Front View Ceiling Plates PRG Series Projector Mount AccessoriesCord Management Capacidad máxima de soportar carga CaracterísticasTabla de contenido Herramientas necesarias para el ensamblajeDescripción Cant. N.o de pieza De pieza Lista de piezasPase al paso Instalación en columnas de extensión / placas de techoInstalación en techos con vigas de madera Instalación en techos de concreto Vista EN Corte No evaluado por UL Instalación profesional solamente Instalación en varillas roscadasFijar la placa adaptadora al proyector Precaución 27 de Conéctelos al proyector Manejo de cableAlinear el proyector Vista Lateral Pieza adaptadora de techo para cerchas Accesorios del Soporte para Proyectores Serie PRGManejo de cables Caractéristiques Table des matières Outils nécessaires au montagePièce no Liste des piècesPassez à l’étape Installation à une colonne d’extension / plaque de plafondInstallation sur des plafonds à solives de bois Installation à un plafond en béton VUE EN Coupe Français Fixation de la plaque d’adaptation au projecteur Mise EN Garde Avertissement Reliez-les au projecteur Gestion des câblesAlignement du projecteur VUE DE Face Adaptateur de plafond à ossature apparente Accessoires du support de projecteur de la série PRGAlligator Limited FIVE-YEAR Warranty Garantía Limitada DE Cinco Años Garantie DE Cinq ANS