Ricoh PJ WX3131, PJ X3241, PJ X3131 owner manual Safety Precautions, USA only

Page 2

Before Using

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

USA only

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

MODEL NAME: PJ X3131 / PJ WX3131 / PJ X3241 USA only

TRADE NAME: DATA PROJECTOR

MODEL NAME: PJ X3131 / PJ WX3131 / PJ X3241

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Image 2

Contents Data Projector Safety Precautions USA onlyEquipment Ventilation Power SourcesSource of Light Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryAttachments AccessoriesDamage Requiring Service Do not use the product in a closed installation location Replacement PartsSafety Check ServicingAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel Video Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Placement StylesPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen size Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftLogo confirmation Reset logoDisplay style Lamp power  The Default setting menuPower on Detailed description Auto input searchClosed Caption Detailed description Fan modeKey lock  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverUsed Lamps Lamp replacementAbout lamp replacement messages Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filter Main unit cleaning Lens and main unit cleaning Lens cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85 List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300