Ricoh PJ X3131, PJ X3241, PJ WX3131 Lamp replacement, About lamp replacement messages, Used Lamps

Page 46

Lamp replacement (Continued)

Notes and Precautions

•The [Lamp time] item in the Status display menu indicates the time of lamp use (as a rough guide) p.42

•Please replace the lamp after 2000 hours of use with [Lamp power] in the Default setting 1 menu set to [Standard], and 3000 hours of use with [Lamp power] in the Default setting 1 menu set to [Low]. p.40

•There are cases that the lamp can not work before the above mentioned period expires or before the replacement message is displayed.

•Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly, the projector may fail to be powered on or the lamp may fail to come on.

•Always replace the lamp with a new one.

•The lamp is made out of glass. Do not touch the glass surface with your bare hands, bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

About lamp replacement messages

•The lamp replacement message of this projector displays an appropriate period according to the use period for [Standard] / [Low] of the [Lamp power] respectively.

•When the replacement time approaches, the message of “The lamp life is ending. Please change the lamp.” is displayed every time the power is turned on. This display disappears when you press the button.

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic mercury. Be careful not to break used lamps, and dispose of them in accordance with local regulations or contact your sales representative.

46

Image 46

Contents Data Projector Safety Precautions USA onlyEquipment Source of Light Power SourcesVentilation Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryDamage Requiring Service AccessoriesAttachments Do not use the product in a closed installation location Replacement PartsSafety Check ServicingMoisture Condensation Place and Manner of InstallationAvoid Volatile Liquid Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel Video Loading dry-cell batteries into the remote control Preparing and using the remote control Operating the remote Control Placement Placement StylesScreen As seen from above As seen from the side Projection Distance and SizePJ WX3131 Screen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen sizePress the remote control’s Freeze button  Setting the password How to change password Freezing the image Freeze How to operate when password is On How to set password from Off to OnHow to set password from On to Off Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftDisplay style Reset logoLogo confirmation Lamp power  The Default setting menuPower on Detailed description Auto input searchKey lock Detailed description Fan modeClosed Caption  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverAbout lamp replacement messages Lamp replacementUsed Lamps Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filter Lens cleaning Lens and main unit cleaning Main unit cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85 List of supported signals Component signals Specifications List of supported signals Video, S-Video signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300