Ricoh PJ WX3131, PJ X3241 Basic operations, Turn on the power, Activate the connected device

Page 26

Basic operations

1Turn on the power.

Turn on the power by following the instructions in “Turning the power on” p.24 .

2Select the language and the lamp power (When using the first time).

When the projector is used for the first time after purchase, the start menu for language (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .)

1Use the , , or button to select the desired language and press the button.

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Turkish

Polish

Norwegian

Finnish

Czech

Hungarian

Greek

Danish

Dutch

Rumanian

Japanese

Chinese (simpliﬁed)

Chinese (traditional)

Korean

Indonesian

Thai

Arabic

Message for setup confirmation is displayed in a selected language.

Then, the menu for lamp power selection and configuration is displayed. It is automatically set as Standard. To change the setting, follow the step 2 .

2Use the or button to select the lamp power and press the button.

The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds.

Notes

•When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting 2 menu p.41 , the start menu will be displayed the next time when the power is turned on.

•The language can also be set via the Display setting menu p.37 and Lamp power via the Default setting 1 menu p.40 .

•This owner’s manual assumes that English has been selected.

3Activate the connected device.

Turn on and start the connected device such as a computer.

4Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals.

26

Image 26

Contents Data Projector Safety Precautions USA onlyEquipment Ventilation Power SourcesSource of Light Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryAttachments AccessoriesDamage Requiring Service Do not use the product in a closed installation location Replacement PartsSafety Check ServicingAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel Video Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Placement StylesPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen size Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftLogo confirmation Reset logoDisplay style Lamp power  The Default setting menuPower on Detailed description Auto input searchClosed Caption Detailed description Fan modeKey lock  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverUsed Lamps Lamp replacementAbout lamp replacement messages Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filter Main unit cleaning Lens and main unit cleaning Lens cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85 List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300