Ricoh PJ WX3131, PJ X3241 Using handy features,  Using auto setting For computer input only

Page 29

Using handy features

Using auto setting (For computer input only)

This function automatically sets up the projector to the optimum state. It sets up sampling phase, frequency and screen position, for each type of the input signal by using simple operations.

Press the remote control’s AUTO SET button.

The icon will appear during processing.

You can set as well by selecting [Auto setting] in the Image adjustment menu p.35 .

Remote control

Notes

•The image may not be projected or auto adjustment/setting may not be performed correctly for input signals other than those supported by the projector p.53 , p.54 .

•If auto setting fails adjustment, adjust manually with [Position] in the Image adjustment menu p.35 .

Correcting the keystone distortion

When the projector placement angle against the screen is changed while projecting the image, the picture will undergo keystone (trapezoidal) distortion.

This projector is capable of correcting this keystone distortion.

Before correction

After correction

•The keystone distortion will be corrected automatically based on the projector’s placement angle.

Adjusting Keystone distortion Manually

		Use the	buttons for keystone adjustment.	Control panel	Remote
		Notes		Control panel	control

• Depending on the amount of keystone adjustment and the content of images, some information may be lost, or the picture quality may suffer.

• Even if [Auto keystone] is set to [On], keystone distortion can be adjusted manually. Note that if you change the position or angle of the projector, automatic keystone correction will be performed again.

•When [Auto keystone] is set to [On], the automatic keystone correction will be performed each time the power is turned on.

•The keystone correction settings are memorized after the power has been turned off. Therefore, it is recommended that you set [Auto keystone] to [Off], if the case is that the projector placement angle against the screen remains unchanged and you do not wish to change the keystone adjustment that you set.

Operations

29

Image 29

Contents Data Projector USA only Safety PrecautionsEquipment Ventilation Power SourcesSource of Light Power Cord Protection CleaningHeat Water and MoistureLightning storms Important Safety InstructionsDo not place the product vertically Object and Liquid EntryAttachments AccessoriesDamage Requiring Service Safety Check Replacement PartsDo not use the product in a closed installation location ServicingAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Copyrights Important Precautions LCD PanelDisposal Following information is only for EU-member statesNotational Conventions Used in This Manual Other Information TrademarksContents Others MaintenanceChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Video Names of the terminals on the rear panel Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Styles PlacementPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Before connection Connection Connecting the power cord Turning the power on and off Turning the power on Removing the lens capPrecautions  Turning the power offPress the ON/STANDBY button again Replace the lens capBasic operations Turn on the powerActivate the connected device Press the Input buttonAdjusting the screen size and focus Projector placement angle adjustmentsAdjusting the volume with the buttons To fine adjust the angle, twist the foot adjusterLCD Panels Basic operations Using auto setting For computer input only Using handy featuresPress the remote control’s Auto SET button Adjusting Keystone distortion ManuallyPress the remote control’s Resize button Using handy featuresTo zoom out, press the remote control’s Resize Button  Resizing image Cutting off the picture and sound temporarily  Changing picture modeMute  Changing screen size Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On  Setup using the Setting display Using the menusFrequency  The image adjustment menuUsing the menus  The display setting menu Precaution Blackboard modeDetailed description Screen size Up/down shiftLogo confirmation Reset logoDisplay style Power on  The Default setting menuLamp power Detailed description Auto input searchClosed Caption Detailed description Fan modeKey lock B/P R  Displaying Information Status displayOperations Unplug power cord Wait until lamp is sufficiently cooled Lamp replacementRemove the outer lamp cover Remove the inner lamp coverPull out the lamp Reset the lamp timeMount the new lamp Replace the inner lamp coverUsed Lamps Lamp replacementAbout lamp replacement messages Unplug power cord Remove the air filter Air filter cleaningClean the filter Replace the air filter Main unit cleaning Lens and main unit cleaning Lens cleaning Power went out during use No powerPower went out during use, or power won’t come on Trouble indicationsTroubleshooting Doesn’t work If This Happens Check Remote control List of general specifications SpecificationsSpecification  Separately sold productSVGA85  List of supported signals RGB signals List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Control terminal  Main Commands Pin assignment  Interface formatEN US EN GB Y006-6300