Ricoh PJ WX3131, PJ X3241, PJ X3131 owner manual Connection, Before connection

Page 23

Connection

Before connection

•Read the owner’s manual of the device you are connecting to the projector.

•Some computers cannot be used with or connected to this projector. Check for an RGB output terminal, supported signal p.53 , etc.

•Turn off the power of both devices before connecting.

•The figure below shows sample connections. This does not mean that all of these devices

can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)

Video recorder,	Computer	DVD video recorder, etc.
DVD player, etc.

	To audio	To	To		Conversion adapter		To audio
				S-video cable	BNC-pin (not supplied)
	output	video	S-video				output
					To Y/CB/CR output
	White (L)/	output	output	(not supplied)			White (L)/
				To RGB output	Green(Y)/Blue(CB)/
	Red (R)						Red (R)
				RGB cable	To audio	Red (CR)

		Video cable		(supplied)	output
	(not supplied)
				Audio cable	Monitor cable Mini
	Audio cable				D-sub 15P-BNC
				(not supplied)
						(not supplied)
	(not supplied)

Audio cable (not supplied)

Preparations

		Control
	Audio cable	cable (not
	Audio cable	supplied)
	(not supplied)	supplied)
	(not supplied)
		To RS-232C
	To audio input	terminal p.55
	White (L)/Red ( R)

Audio amplifier, etc.

Computer (for control)

Monitor

It is necessary to switch to MONITOR OUT by the switch. p.18

* The connection for COMPUTER 1 IN terminal described here is also applicable for COMPUTER 2 IN terminal.

Notes

•When COMPUTER 2 IN terminal is used as MONITOR OUT terminal, the signal which is input to COMPUTER 1 IN terminal is output.

•Signals are output from MONITOR OUT terminal even in standby mode. However, from AUDIO OUT terminal, no audio signal is output.

•A computer monitor cannot accept Y/PB/PR signals correctly.

•The AUDIO IN terminal can be used for devices connected to COMPUTER 1 terminal, COMPUTER 2 terminal, VIDEO terminal and S-VIDEO terminal.

•When an AUDIO OUT terminal is connected, sound is not output from the projector speaker.

•Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

23

Image 23

Contents Data Projector USA only Safety PrecautionsEquipment Ventilation Power SourcesSource of Light Water and Moisture CleaningPower Cord Protection HeatObject and Liquid Entry Important Safety InstructionsLightning storms Do not place the product verticallyAttachments AccessoriesDamage Requiring Service Servicing Replacement PartsSafety Check Do not use the product in a closed installation locationAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Following information is only for EU-member states Important Precautions LCD PanelCopyrights DisposalNotational Conventions Used in This Manual Other Information TrademarksContents Others MaintenanceChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Video Names of the terminals on the rear panel Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Styles PlacementPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Before connection ConnectionRemoving the lens cap Turning the power on and off Connecting the power cord  Turning the power onReplace the lens cap  Turning the power offPrecautions Press the ON/STANDBY button againPress the Input button Turn on the powerBasic operations Activate the connected deviceTo fine adjust the angle, twist the foot adjuster Projector placement angle adjustmentsAdjusting the screen size and focus Adjusting the volume with the buttonsLCD Panels Basic operationsAdjusting Keystone distortion Manually Using handy features Using auto setting For computer input only Press the remote control’s Auto SET button Resizing image Using handy featuresPress the remote control’s Resize button To zoom out, press the remote control’s Resize Button Changing screen size  Changing picture mode Cutting off the picture and sound temporarily Mute Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On  Setup using the Setting display Using the menusFrequency  The image adjustment menuUsing the menus  The display setting menu Up/down shift Blackboard modePrecaution Detailed description Screen sizeLogo confirmation Reset logoDisplay style Detailed description Auto input search  The Default setting menuPower on Lamp powerClosed Caption Detailed description Fan modeKey lock B/P R  Displaying Information Status displayOperations Remove the inner lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the outer lamp coverReplace the inner lamp cover Reset the lamp timePull out the lamp Mount the new lampUsed Lamps Lamp replacementAbout lamp replacement messages Replace the air filter Air filter cleaningUnplug power cord Remove the air filter Clean the filter Main unit cleaning Lens and main unit cleaning Lens cleaning Trouble indications No powerPower went out during use Power went out during use, or power won’t come onTroubleshooting Doesn’t work If This Happens Check Remote control Separately sold product Specifications List of general specifications SpecificationSVGA85  List of supported signals RGB signals List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Interface format  Main Commands Control terminal  Pin assignmentEN US EN GB Y006-6300