Ricoh PJ X3241, PJ X3131, PJ WX3131 owner manual  Displaying Information Status display, B/P R

Page 42

Using the menus (Continued)

Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item	Description	Computer	Y/PB/PR	Video	S-video

Input	Input source name	Yes	Yes	Yes	Yes

Mode name	RGB input mode [Note 1]	Yes	No	No	No
Resolution	Resolution (in dots)	Yes	No	No	No

Frequency	Sync frequency	Yes	No	No	No

Sync	Sync signal polarity [Note 2]	Yes	No	No	No
Signal format	Y/PB/PR signal format	No	Yes	No	No

Video mode	Color method of video signal	No	No	Yes	Yes
Lamp time	Time of lamp use [Note 3]	Yes	Yes	Yes	Yes
Lamp reset count	The count for lamp replacement	Yes	Yes	Yes	Yes

Total time	The total time that this projector is	Yes	Yes	Yes	Yes
	used.	Yes	Yes	Yes	Yes
	used.
Version	Firmware version [Note 4]	Yes	Yes	Yes	Yes

Notes

1:The mode of supported RGB signals p.53 is shown.

2:Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3:Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.)

4:[Version] shows the version of the projector’s internal control program. This version will be requested for customer service purposes.

Note

•The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again.

42

Image 42

Contents Data Projector Safety Precautions USA onlyEquipment Power Sources Source of LightVentilation Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryAccessories Damage Requiring ServiceAttachments Do not use the product in a closed installation location Replacement PartsSafety Check ServicingPlace and Manner of Installation Moisture CondensationAvoid Volatile Liquid Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel VideoPreparing and using the remote control  Loading dry-cell batteries into the remote control Operating the remote Control Placement Placement StylesProjection Distance and Size Screen As seen from above As seen from the sidePJ WX3131 Screen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen size Setting the password How to change password Press the remote control’s Freeze button Freezing the image Freeze How to set password from Off to On How to operate when password is OnHow to set password from On to Off Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftReset logo Display styleLogo confirmation Lamp power  The Default setting menuPower on Detailed description Auto input searchDetailed description Fan mode Key lockClosed Caption  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverLamp replacement About lamp replacement messagesUsed Lamps Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filterLens and main unit cleaning  Lens cleaning Main unit cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85Specifications  List of supported signals Component signals List of supported signals Video, S-Video signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300