Ricoh PJ X3131, PJ X3241, PJ WX3131 owner manual Using the menus,  Setup using the Setting display

Page 34

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using the MENU button p.16 on the control panel (main unit side) and remote control.

Setup using the Setting display

The menu shown below is for operation instructions purposes and might differ from the actual display.

1.Press the MENU button Display the Setting display menu.

2.Select a Category

Select a category by using . There are following 5 categories:

Image adjustment menu p.35

Display setting menu	p.37
Default setting 1 menu	p.40
Default setting 2 menu	p.41
Status display menu	p.42

Displays the current adjustments and settings of selected category.

Item shown with gray cannot be adjusted with the current input source.

3.Adjustments & Settings Press or to open the menu.

Item

Adjustment/Setting Value

	These marks signify
	the items can be							These marks signify
	adjusted/set by using							These marks signify
	adjusted/set by using				These marks			that there are setting
	.				These marks			that there are setting
	.				signify that there			screens. Press		or
					signify that there			screens. Press		or
					are options.				to display a list of
					are options.				to display a list of
					Press	or		setting screens.
					Press	or		setting screens.
					to display a list of
These marks signify the items can					options.			* When no item is
					options.

be selected from the list by using									changed, press	.
.
After an item is selected, apply it by					Toggle items with		.
pressing	.				Select items with			and press	.
					Fix selection with		.

•The figure shows displays given for operation instructions purposes. As the display may differ depending on the item, refer to the following applicable pages for the menu item you desire.

•To return to previous item, press the RETURN button.

4. End Press the MENU button once more.

(The menu will disappear automatically after 30 seconds, if no operation is conducted.)

34

Image 34

Contents Data Projector Safety Precautions USA onlyEquipment Source of Light Power SourcesVentilation Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryDamage Requiring Service AccessoriesAttachments Do not use the product in a closed installation location Replacement PartsSafety Check ServicingMoisture Condensation Place and Manner of InstallationAvoid Volatile Liquid Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel Video Loading dry-cell batteries into the remote control Preparing and using the remote control Operating the remote Control Placement Placement StylesScreen As seen from above As seen from the side Projection Distance and SizePJ WX3131 Screen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen sizePress the remote control’s Freeze button  Setting the password How to change password Freezing the image Freeze How to operate when password is On How to set password from Off to OnHow to set password from On to Off Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftDisplay style Reset logoLogo confirmation Lamp power  The Default setting menuPower on Detailed description Auto input searchKey lock Detailed description Fan modeClosed Caption  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverAbout lamp replacement messages Lamp replacementUsed Lamps Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filter Lens cleaning Lens and main unit cleaning Main unit cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85 List of supported signals Component signals Specifications List of supported signals Video, S-Video signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300