Ricoh PJ X3131 Trouble indications, No power, Lamp went out during use, or won’t come on

Page 49

Others

Trouble indications

The indicator illuminates and a beep sound informs you of internal abnormalities.

		No power
	(OFF)	⇒ Problem with projector
	(OFF)	• Unplug the power cord, and contact your sales representative.

				Lamp went out during use, or won’t come on
				⇒ Lamp temperature is high so that it is difficult to turn on, the
(Red	(Red lit)			lifetime of the lamp has ended or the projector is malfunctioning.
flashing)				• Unplug the power cord and wait for a short while, then turn the
	or
	or			power back on.
				power back on.

• If a lamp burns out, replace it with a new one.

(Red lit) (Red lit)

			Power went out during use
			⇒ Internal overheating, or the outside temperature is too high.
	flashing) (Red lit)
	flashing) (Red lit)		• Place the projector so that the air intake and exhaust are not
	(Red
			blocked.

•Unplug the power cord and wait for a short while, then turn the power back on.

The icon will appear before the power goes out.

			Power went out during use
			⇒ Problem with internal cooling fan.

(Green	(Red lit)		• Unplug the power cord, and contact your sales representative.
flashing)			The	icon will appear before the power goes out.

					Power went out during use, or power won’t come on
	(Orange				⇒ The lamp cover is not properly attached.
	(Orange	(Red lit)			• Unplug the power cord, and reattach the lamp cover. p.44
	flashing)	(Red lit)			• Unplug the power cord, and reattach the lamp cover. p.44

			Power went out during use
			⇒ Problem inside the projector.
	(Orange lit) (Red lit)		⇒ Problem inside the projector.
	(Orange lit) (Red lit)		• Unplug the power cord and wait for a short while, then turn the
			power back on.

•If the above action will not clear the problem, unplug the power cord, and contact your sales representative.

The icon will appear before the power goes out.

Note

•After there is an abnormal indication, the abnormal status remains until the power cord is unplugged.

Others

49

Image 49

Contents Data Projector USA only Safety PrecautionsEquipment Source of Light Power SourcesVentilation Power Cord Protection CleaningHeat Water and MoistureLightning storms Important Safety InstructionsDo not place the product vertically Object and Liquid EntryDamage Requiring Service AccessoriesAttachments Safety Check Replacement PartsDo not use the product in a closed installation location ServicingMoisture Condensation Place and Manner of InstallationAvoid Volatile Liquid Copyrights Important Precautions LCD PanelDisposal Following information is only for EU-member statesNotational Conventions Used in This Manual Other Information TrademarksContents Others MaintenanceChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Video Names of the terminals on the rear panel Loading dry-cell batteries into the remote control Preparing and using the remote control Operating the remote Control Placement Styles PlacementScreen As seen from above As seen from the side Projection Distance and SizePJ WX3131 Screen As seen from above As seen from the side Placement Before connection Connection Connecting the power cord Turning the power on and off Turning the power on Removing the lens capPrecautions  Turning the power offPress the ON/STANDBY button again Replace the lens capBasic operations Turn on the powerActivate the connected device Press the Input buttonAdjusting the screen size and focus Projector placement angle adjustmentsAdjusting the volume with the buttons To fine adjust the angle, twist the foot adjusterLCD Panels Basic operations Using auto setting For computer input only Using handy featuresPress the remote control’s Auto SET button Adjusting Keystone distortion ManuallyPress the remote control’s Resize button Using handy featuresTo zoom out, press the remote control’s Resize Button  Resizing image Cutting off the picture and sound temporarily  Changing picture modeMute  Changing screen sizePress the remote control’s Freeze button  Setting the password How to change password Freezing the image Freeze How to operate when password is On How to set password from Off to OnHow to set password from On to Off  Setup using the Setting display Using the menusFrequency  The image adjustment menuUsing the menus  The display setting menu Precaution Blackboard modeDetailed description Screen size Up/down shiftDisplay style Reset logoLogo confirmation Power on  The Default setting menuLamp power Detailed description Auto input searchKey lock Detailed description Fan modeClosed Caption B/P R  Displaying Information Status displayOperations Unplug power cord Wait until lamp is sufficiently cooled Lamp replacementRemove the outer lamp cover Remove the inner lamp coverPull out the lamp Reset the lamp timeMount the new lamp Replace the inner lamp cover About lamp replacement messages Lamp replacement Used Lamps Unplug power cord Remove the air filter Air filter cleaningClean the filter Replace the air filter Lens cleaning Lens and main unit cleaning Main unit cleaning Power went out during use No powerPower went out during use, or power won’t come on Trouble indicationsTroubleshooting Doesn’t work If This Happens Check Remote control List of general specifications SpecificationsSpecification  Separately sold productSVGA85  List of supported signals RGB signals List of supported signals Component signals Specifications List of supported signals Video, S-Video signals  Control terminal  Main Commands Pin assignment  Interface formatEN US EN GB Y006-6300