Ricoh PJ WX3131 Detailed description Screen size, Up/down shift, Blackboard mode, Precaution

Page 38

Using the menus (Continued)

Detailed description [Screen size]

Normal

: Enlarge an input image to fit the screen without changing the aspect

 

 

ratio of video signals.

Full

: Displays an input image in 1024 × 768 dot resolution by enlarging it to

 

 

fill the entire screen. (X3131/X3241)

 

 

Displays an input image in 1280 x 800 dot resolution by enlarging it to

 

 

fill the entire screen. (WX3131)

Thru

: Displays an input image in the native resolution of the video signals. Thru

 

 

display is not available for Y/PB/PR, Video and S-Video-input images.

 

 

The larger image than the screen size will be displayed over the

 

 

screen. The input image may appear vertically long with some

 

 

frequencies of video signals.

Wide

: Displays an input image in the center of the screen with a 16:9 aspect

 

(X3131/

ratio by enlarging it to fit the width of the screen. The upper and lower

 

X3241)

portions of the image will be compressed.

 

 

Wide display is not available for Computer-input images.

4:3 zoom : Displays an input image with a 4:3 aspect ratio by enlarging it (WX3131) vertically. The enlarged image will be displayed over the screen.

4:3 zoom display is not available for computer images.

For Y/PB/PR input, screen size setting function is not available for the video signals with a 16:9 aspect ratio.

Note

If you use the screen size setting function on commercial video software, broadcast or cable-broadcasting programs to display images with the varying aspect ratio except for the purpose of your private viewing and listening, it may infringe the copyright protected by the copyright laws.

[Up/down shift]

Shifts the projected image vertically when [Screen size] is [Wide] for X3131/X3241. Shifts the projected image vertically when [Screen size] is [4:3 zoom] for WX3131.

[Blackboard mode]

Projects the image in colors more like projecting on a screen.

Precaution

The projected image may differ depending on the type, color, and material of the blackboard and wall even if the selected color is the same as the projected screens.

[Background]

RICOH is set for [Logo] by factory setting.

If user’s logo has been registered, it is displayed when [Logo] is set for background.

[Start-up screen]

If user’s logo has been registered and this setting is [On], the logo is displayed at start-up.

[User logo]

Registers a part of the image that is input from computer, as a stationary picture and displays it as a logo at start-up and when no signal is input.

38

Image 38
Contents Data Projector Safety Precautions USA onlyEquipment Ventilation Power SourcesSource of Light Heat CleaningPower Cord Protection Water and MoistureDo not place the product vertically Important Safety InstructionsLightning storms Object and Liquid EntryAttachments AccessoriesDamage Requiring Service Do not use the product in a closed installation location Replacement PartsSafety Check ServicingAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Disposal Important Precautions LCD PanelCopyrights Following information is only for EU-member statesOther Information Trademarks Notational Conventions Used in This ManualContents Maintenance OthersChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Names of the terminals on the rear panel Video Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Placement StylesPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Connection Before connection Turning the power on Turning the power on and off Connecting the power cord Removing the lens capPress the ON/STANDBY button again  Turning the power offPrecautions Replace the lens capActivate the connected device Turn on the powerBasic operations Press the Input buttonAdjusting the volume with the buttons Projector placement angle adjustmentsAdjusting the screen size and focus To fine adjust the angle, twist the foot adjusterBasic operations LCD PanelsPress the remote control’s Auto SET button Using handy features Using auto setting For computer input only Adjusting Keystone distortion ManuallyTo zoom out, press the remote control’s Resize Button Using handy featuresPress the remote control’s Resize button  Resizing imageMute  Changing picture mode Cutting off the picture and sound temporarily  Changing screen size Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On Using the menus  Setup using the Setting display The image adjustment menu FrequencyUsing the menus  The display setting menu Detailed description Screen size Blackboard modePrecaution Up/down shiftLogo confirmation Reset logoDisplay style Lamp power  The Default setting menuPower on Detailed description Auto input searchClosed Caption Detailed description Fan modeKey lock  Displaying Information Status display B/P ROperations Remove the outer lamp cover Lamp replacementUnplug power cord Wait until lamp is sufficiently cooled Remove the inner lamp coverMount the new lamp Reset the lamp timePull out the lamp Replace the inner lamp coverUsed Lamps Lamp replacementAbout lamp replacement messages Clean the filter Air filter cleaningUnplug power cord Remove the air filter Replace the air filter Main unit cleaning Lens and main unit cleaning Lens cleaning Power went out during use, or power won’t come on No powerPower went out during use Trouble indicationsTroubleshooting If This Happens Check Remote control Doesn’t workSpecification Specifications List of general specifications  Separately sold product List of supported signals RGB signals SVGA85 List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Pin assignment  Main Commands Control terminal  Interface formatEN US EN GB Y006-6300