Ricoh PJ X3241, PJ X3131 Pull out the lamp, Mount the new lamp, Replace the inner lamp cover

Page 45

5 Pull out the lamp.

Loosen the 3 lamp locking screws, pull up the handle, and press the tab to remove the lamp.

Tab

6Mount the new lamp.

Align the orientation, press down the new lamp until the bottom is reached, and lock in place using the 3 lamp locking screws.

7Replace the inner lamp cover.

Reattach both screws removed in step 4 .Tighten the screws until the inner lamp cover is fully immobile.

8Replace the outer lamp cover.

Reseat the outer lamp cover by sliding it in the direction of the arrows (as shown in the illustration), and then tighten the screw loosened in step 3 .

Tighten the screw until the outer lamp cover is fully immobile. (The outer lamp cover must be attached.)

9Reset the lamp time.

See the lamp’s manual for instructions on resetting the lamp time.

Inner lamp cover

Outer lamp cover

Maintenance

Image 45

Contents Data Projector USA only Safety PrecautionsEquipment Power Sources Source of LightVentilation Power Cord Protection CleaningHeat Water and MoistureLightning storms Important Safety InstructionsDo not place the product vertically Object and Liquid EntryAccessories Damage Requiring ServiceAttachments Safety Check Replacement PartsDo not use the product in a closed installation location ServicingPlace and Manner of Installation Moisture CondensationAvoid Volatile Liquid Copyrights Important Precautions LCD PanelDisposal Following information is only for EU-member statesNotational Conventions Used in This Manual Other Information TrademarksContents Others MaintenanceChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Video Names of the terminals on the rear panelPreparing and using the remote control  Loading dry-cell batteries into the remote control Operating the remote Control Placement Styles PlacementProjection Distance and Size Screen As seen from above As seen from the sidePJ WX3131 Screen As seen from above As seen from the side Placement Before connection Connection Connecting the power cord Turning the power on and off Turning the power on Removing the lens capPrecautions  Turning the power offPress the ON/STANDBY button again Replace the lens capBasic operations Turn on the powerActivate the connected device Press the Input buttonAdjusting the screen size and focus Projector placement angle adjustmentsAdjusting the volume with the buttons To fine adjust the angle, twist the foot adjusterLCD Panels Basic operations Using auto setting For computer input only Using handy featuresPress the remote control’s Auto SET button Adjusting Keystone distortion ManuallyPress the remote control’s Resize button Using handy featuresTo zoom out, press the remote control’s Resize Button  Resizing image Cutting off the picture and sound temporarily  Changing picture modeMute  Changing screen size Setting the password How to change password Press the remote control’s Freeze button Freezing the image Freeze How to set password from Off to On How to operate when password is OnHow to set password from On to Off  Setup using the Setting display Using the menusFrequency  The image adjustment menuUsing the menus  The display setting menu Precaution Blackboard modeDetailed description Screen size Up/down shiftReset logo Display styleLogo confirmation Power on  The Default setting menuLamp power Detailed description Auto input searchDetailed description Fan mode Key lockClosed Caption B/P R  Displaying Information Status displayOperations Unplug power cord Wait until lamp is sufficiently cooled Lamp replacementRemove the outer lamp cover Remove the inner lamp coverPull out the lamp Reset the lamp timeMount the new lamp Replace the inner lamp coverLamp replacement About lamp replacement messagesUsed Lamps Unplug power cord Remove the air filter Air filter cleaningClean the filter Replace the air filterLens and main unit cleaning  Lens cleaning Main unit cleaning Power went out during use No powerPower went out during use, or power won’t come on Trouble indicationsTroubleshooting Doesn’t work If This Happens Check Remote control List of general specifications SpecificationsSpecification  Separately sold productSVGA85  List of supported signals RGB signalsSpecifications  List of supported signals Component signals List of supported signals Video, S-Video signals  Control terminal  Main Commands Pin assignment  Interface formatEN US EN GB Y006-6300