Ricoh PJ WX3131 Heat, Water and Moisture, Cleaning, Be sure that you firmly, Outlet, Overloading

Page 5

5. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like.

7.Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Always use a soft cloth for cleaning.

8. Be sure that you firmly

Using

insert the plug into the wall

 

outlet.

 

Incorrect or faulty connections

Before

may result in fire or electric shock.

 

Avoid using an unsound or loose

 

outlet.

 

9. Power Cord Protection

 

 

Power cords should be routed

 

so that they are not likely to be

 

walked on or pinched by items

 

placed upon or against them,

 

paying particular attention to cords

 

at plugs, convenience receptacles,

 

and the point where they exit from

 

the product.

 

10. Overloading

 

Do not overload wall outlets. To

 

reduce the risk of electric shock,

 

do not use the polarized plug with

 

an extension cord , receptacle, or

 

other outlet unless the blades can

 

be inserted completely with three-

 

wire grounding type to prevent

 

blade exposure. Failure to follow

 

these instructions may result in fire

 

or electric shock.

 

Image 5
Contents Data Projector USA only Safety PrecautionsEquipment Ventilation Power SourcesSource of Light Power Cord Protection CleaningHeat Water and MoistureLightning storms Important Safety InstructionsDo not place the product vertically Object and Liquid EntryAttachments AccessoriesDamage Requiring Service Safety Check Replacement PartsDo not use the product in a closed installation location ServicingAvoid Volatile Liquid Place and Manner of InstallationMoisture Condensation Copyrights Important Precautions LCD PanelDisposal Following information is only for EU-member statesNotational Conventions Used in This Manual Other Information TrademarksContents Others MaintenanceChecking the package contents Names of each part on the main unit Names of each part on the control panel and remote control Preparations Video Names of the terminals on the rear panel Operating the remote Control Preparing and using the remote control Loading dry-cell batteries into the remote control Placement Styles PlacementPJ WX3131 Screen As seen from above As seen from the side Projection Distance and SizeScreen As seen from above As seen from the side Placement Before connection Connection Connecting the power cord Turning the power on and off Turning the power on Removing the lens capPrecautions  Turning the power offPress the ON/STANDBY button again Replace the lens capBasic operations Turn on the powerActivate the connected device Press the Input buttonAdjusting the screen size and focus Projector placement angle adjustmentsAdjusting the volume with the buttons To fine adjust the angle, twist the foot adjusterLCD Panels Basic operations Using auto setting For computer input only Using handy featuresPress the remote control’s Auto SET button Adjusting Keystone distortion ManuallyPress the remote control’s Resize button Using handy featuresTo zoom out, press the remote control’s Resize Button  Resizing image Cutting off the picture and sound temporarily  Changing picture modeMute  Changing screen size Freezing the image Freeze  Setting the password How to change passwordPress the remote control’s Freeze button How to set password from On to Off How to set password from Off to OnHow to operate when password is On  Setup using the Setting display Using the menusFrequency  The image adjustment menuUsing the menus  The display setting menu Precaution Blackboard modeDetailed description Screen size Up/down shiftLogo confirmation Reset logoDisplay style Power on  The Default setting menuLamp power Detailed description Auto input searchClosed Caption Detailed description Fan modeKey lock B/P R  Displaying Information Status displayOperations Unplug power cord Wait until lamp is sufficiently cooled Lamp replacementRemove the outer lamp cover Remove the inner lamp coverPull out the lamp Reset the lamp timeMount the new lamp Replace the inner lamp coverUsed Lamps Lamp replacementAbout lamp replacement messages Unplug power cord Remove the air filter Air filter cleaningClean the filter Replace the air filter Main unit cleaning Lens and main unit cleaning Lens cleaning Power went out during use No powerPower went out during use, or power won’t come on Trouble indicationsTroubleshooting Doesn’t work If This Happens Check Remote control List of general specifications SpecificationsSpecification  Separately sold productSVGA85  List of supported signals RGB signals List of supported signals Video, S-Video signals Specifications List of supported signals Component signals  Control terminal  Main Commands Pin assignment  Interface formatEN US EN GB Y006-6300