Samsung spinpoint v40, 3.5" hard disk drives manual System Setup

Page 30

INSTALLATION

addressing mode.

•Windows 95 or 98 that use FAT16 file system will limit the drive’s logical partition at 2.1GB per logical drive. Windows95 OSR2 or later allow for the FAT32 file system which provides access to greater than 2GBof logical capacity.

•A low-level format is not required, as this was done at the factory before shipment.

4.7.1Drive Installation to Access the Full Capacity Using 32GB Clip

A system hang condition is identified when the installation of a hard disk drive larger than 32GB is attempted into a PC system that incorporates specific older BIOS’. This issue is caused by the older BIOS’ inability to support the full capacity of the hard disk drive, not by the SpinPoint V40 hard disk drive.

One solution to this issue, is to contact the system or motherboard manufacturer and upgrade the BIOS (to enable the system to access the full capacity of the hard disk drive).

As an alternative solution, the drive can be installed by using a 32GB clip jumper on the SpinPoint V40 hard disk drive, along with the Disk Manager utility program. To set up the drive using 32GB clip, follow the instructions provided below:

1.Install a 32 GB clip jumper (see section 4.5).

2.Boot up the system, enter SYSTEM SETUP, change the settings for the drive to “Auto”, and exit

SYSTEM SETUP.

NOTE: At this point in the installation, the drive capacity is limited to 32GB. No further steps are needed if the drive is intended to be used as 32 gigabytes.

3.To access the full capacity, reboot the system with the Disk Manager diskette. Disk Manager will install Dynamic Drive Overlay on the drive. The Dynamic Drive Overlay will take control of the drive from the BIOS each time the system is booted, and enable access to the entire capacity of the drive.

4.Select “Easy Disk Installation”

5.Select drive to be installed (master or slave)

6.Select the operating system (Win95 OSR2, 98, 98SE, Me, 2000, or NT)

7.Follow the instruction to format drive

NOTE;

Microsoft identified a 32GB capacity limitation issue with the Windows 95 operating system. The solutions provided above do not overcome the capacity limitation of the Windows 95 operating system. Microsoft recommends that Windows 95 customers who want to use media larger than 32GB, upgrade to Microsoft Windows 98 or Microsoft Windows NT. For more information, please check Microsoft Knowledgebase.

22

SpinPoint V40 Product Manual

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Spinpoint SpinPoint V40 Product Manual Table of Contents Ervo S Ystem EAD and W Rite O Perations Irmware F EaturesSmart Programming Requirements Protocol OverviewTiming 107 Maintenance PrecautionsService and Repair General InformationTable of Figures Page User Definition Manual OrganizationScope Computer Message Commands and MessagesTerminology and Conventions Format C/SReference Key Features IntroductionDescription Standards and Regulations Hardware RequirementsSpecification Summary SpecificationsPhysical Specifications Logical ConfigurationsPerformance Specifications Power Requirements 28.71Environmental Specifications SV6003H SV6014H SV8004HReliability Specifications Mtbf POHInstallation Space RequirementsUnpacking Instructions MountingOrientation 2Mounting Dimensions in Millimeters Clearance 3Mounting-Screw ClearanceAT-Bus Interface Connector Cable ConnectorsDC Power Connector VentilationSpinPoint V40 Product Manual Jumper Block Configurations Options for Jumper Block Configuration Drive Installation 7DC Power Connector and AT-Bus Interface Cable ConnectionsSystem Startup Procedure ParameterSystem Setup DC Spindle Motor Assembly Head / Disk Assembly HDABase Casting Assembly Disk Drive OperationExploded Mechanical View Voice Coil Motor and Actuator Latch Assemblies Disk Stack AssemblyHead Stack Assembly Air Filtration SystemDigital Signal Process and Interface Controller Drive ElectronicsAT Disk Controller 2SID2001 AT Controller Block Diagram Host Interface Control Block Buffer Control Block Disk Control BlockSpinPoint V40 Product Manual Disk ECC Control Block Power ManagementRead/Write IC Frequency SynthesizerAsymmetry Correction Circuitry ASC Time Base GeneratorAutomatic Gain Control Analog Anti-Aliasing Low Pass Filter3Read/Write 88C5200 Servo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Multi-burst ECC Correction Defect ManagementAutomatic Defect Allocation SmartBlank Signal Conventions Signal SummaryPhysical Interface Signal Descriptions Intrq Drive Interrupt DMACK- DMA AcknowledgeDmarq DMA Request IOCS16- Drive 16-bit I/OPDIAG- Passed Diagnostics RESET- Drive ResetIordy I/O Channel Ready SD3 SD8 SD6 SD9 SD5SD4 SD2Drive Drive HostDIR Bit Conventions Logical InterfaceGeneral EnvironmentSpinPoint V40 Product Manual Control Block Registers Command Block Registers2 I/O Register Address N N N A a aDrive Address Register 3F7h Control Block Register DescriptionsAlternate Status Register 3F6h Device Control Register 3F6hError Register 1F1h Command Block Register DescriptionsFeatures Register 1F1h Data Register 1F0hCylinder High Register 1F5h Command Register 1F7hSector Count Register 1F2h Cylinder Low Register 1F4hStatus Register 1F7h BSY Drdy DWF DSC DRQ Corr IDX ERRAt Command Register Descriptions Command Parameter Used SpinPoint V40 Product Manual Check Power Mode 98h, E5h Execute Device Diagnostics 90hDownload Micro Code 92h Flush Cache E7h Format Track 50hIdentify Device ECh Word Content Description XxxxCapabilities Command set supported 95-128 0000h Reserved 129-159 Vendor specific 160-255 Idle 97h,E3h Idle Immediate 95h,E1hInitialize Device Parameters 91h Read Buffer E4h Read Long 22hwith retry, 23h without retryRead Multiple Command C4h Read Native Max Address F8h Read Sectors 20hwith retry, 21hwithout retryRead Verify Sectors 40hwith retry, 41hwithout retry Recalibrate 1xhSeek 7xh Set Features EFh ModeNormal outputs InputsLBA BSY Drdy DRQ ERRDescription Set Multiple Mode C6h Sleep 99h, E6hSmart disable operation D9h Standby 96h,E2hSmart B0h Smart enable/disable attribute autosave D2h Smart enable operations D8hSmart execute off-line immediate D4h Smart read data D0h Byte DescriptionsValue Definition Off-line data collection capabilitySmart return status DAh Smart capabilitySmart read log sector D5h Smart save attribution value D3hWrite Buffer E8h Standby 96h, E2hStandby Immediate 94h, E0h Write DMA CAhWrite Multiple Command C5h Write Sectors 30hwith retry, 31hwithout retrySpinPoint V40 Product Manual Reset Response Error PostingProgramming Requirements Command Error Register Status Register BBKStandby mode Power ConditionsSleep mode Idle modeNormal mode PIO Data in Commands Protocol OverviewPIO Data Out Commands PIO Read CommandPIO Read Aborted Command BSY=0 DRDY=1 BSY=1 PIO Write CommandPIO Write Aborted Command BSY=0 DRQ=1 BSY=1 DRQ=0Non-Data Commands DMA Data Transfer Commands Aborted DMA Command Initialize DMA Reset DMA Status BSY=0 BSY=1BSY=1 BSY=0 Timing Register transfersDIOR-/DIOW Write PIO timing parameters Mode PIO data transfersAddr valid See note T1 t2 DIOR-/DIOW Multiword DMA data transfer DIOR-/DIOWMultiword DMA timing parameters Mode Ultra DMA data transfer Initiating an Ultra DMA data in burstUltra DMA data burst timing requirements 19Ultra DMA data burst timing requirementsSustained Ultra DMA data in burst 5Sustained Ultra DMA data in burstHost pausing an Ultra DMA data in burst 6Host pausing an Ultra DMA data in burstDevice terminating an Ultra DMA data in burst 7Device terminating an Ultra DMA data in burst 100Host terminating an Ultra DMA data in burst 8Host terminating an Ultra DMA data in burstInitiating an Ultra DMA data out burst 9Initiating an Ultra DMA data out burst 102Sustained Ultra DMA data out burst 10Sustained Ultra DMA data out burstDevice pausing an Ultra DMA data out burst 11Device pausing an Ultra DMA data out burst 104Host terminating an Ultra DMA data out burst 12Host terminating an Ultra DMA data out burstDevice terminating an Ultra DMA data out burst 13Device terminating an Ultra DMA data out burst 106Maintenance Precautions Service And RepairGeneral Information
Top Page Image Contents