Samsung spinpoint v40, 3.5" hard disk drives manual Inputs, Lba, Normal outputs, BSY Drdy DRQ ERR

Page 76

DISK DRIVE OPERATION

6.4.20 Set Max Address (F9h)

Host Protected Area feature set.

Inputs

Register	7	6	5		4	3	2	1	0
Features						Na
Sector Count					Na				VV
Sector Number		Native max address sector number or SET MAX LBA
Cylinder Low				SET MAX cylinder low or LBA
Cylinder High				SET MAX cylinder high or LBA
Device/Head	obs	LBA	obs		DEV	Native max address head number or
							SET MAX LBA
Command						F9h

Sector Count –

VV(Value volatile). If bit 0 is set to one, the device shall preserve the maximum values over power- up or hardware reset. If bit 0 is cleared to zero, the device shall revert to the most recent non-volatile maximum address value setting over power-up or hardware reset.

Sector Number –

Contains the native max address sector number (IDENTIFY DEVICE word 6) or LBA bits (7:0) value to be set.

Cylinder Low –

Contains the maximum cylinder low or LBA bits (15:8) value to be set. Cylinder High –

Contains the maximum cylinder high or LBA bits (23:16) value to be set. Device/Head –

If LBA is set to one, the maximum address value is an LBA value.

If LBA is cleared to zero, the maximum address value is a CHS value. DEV shall indicate the selected device.

Bits (3:0) contain the native max address head number (IDENTIFY DEVICE word 3 minus one) or LBA bits (27:24) value to be set.

Normal outputs

Register	7	6	5	4	3		2	1			0
Error						Na
Sector Count						Na
Sector Number			Native max address sector number or LBA
Cylinder Low			Native max address cylinder low or LBA
Cylinder High			Native max address cylinder high or LBA
Device/Head	obs	LBA	obs	LBA		Native max address head or LBA
Status	BSY	DRDY	DF	na		DRQ	na	na			ERR

Sector Number –

Maximum native sector number or LBA bits (7:0) set on the device. Cylinder Low –

Maximum cylinder number low or LBA bits (15:8) set on the device. Cylinder High –

Maximum cylinder number high or LBA bits (23:16) set on device. Device/Head –

DEV shall indicate the selected device.

maximum native head number or LBA bits (27:24) set on the device. Status register –

BSY shall be cleared to zero indicating command completion.

68	SpinPoint V40 Product Manual

Image 76

Contents Spinpoint SpinPoint V40 Product Manual Table of Contents Irmware F Eatures Ervo S Ystem EAD and W Rite O PerationsSmart Protocol Overview Programming RequirementsTiming Maintenance Precautions Service and Repair107 General InformationTable of Figures Page Manual Organization User DefinitionScope Commands and Messages Terminology and ConventionsComputer Message Format C/SReference Introduction Key FeaturesDescription Standards and Regulations Hardware RequirementsSpecification Summary SpecificationsPhysical Specifications Logical ConfigurationsPerformance Specifications Power Requirements 28.71Environmental Specifications SV6003H SV6014H SV8004HReliability Specifications Mtbf POHInstallation Space RequirementsMounting Unpacking InstructionsOrientation 2Mounting Dimensions in Millimeters Clearance 3Mounting-Screw ClearanceCable Connectors DC Power ConnectorAT-Bus Interface Connector VentilationSpinPoint V40 Product Manual Jumper Block Configurations Options for Jumper Block Configuration Drive Installation 7DC Power Connector and AT-Bus Interface Cable ConnectionsSystem Startup Procedure ParameterSystem Setup Head / Disk Assembly HDA Base Casting AssemblyDC Spindle Motor Assembly Disk Drive OperationExploded Mechanical View Disk Stack Assembly Head Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration SystemDrive Electronics Digital Signal Process and Interface ControllerAT Disk Controller 2SID2001 AT Controller Block Diagram Host Interface Control Block Buffer Control Block Disk Control BlockSpinPoint V40 Product Manual Power Management Read/Write ICDisk ECC Control Block Frequency SynthesizerTime Base Generator Automatic Gain ControlAsymmetry Correction Circuitry ASC Analog Anti-Aliasing Low Pass Filter3Read/Write 88C5200 Read and Write Operations Servo SystemRead Channel Write Channel Firmware FeaturesRead Caching Write Caching Defect Management Automatic Defect AllocationMulti-burst ECC Correction SmartBlank Signal Summary Signal ConventionsPhysical Interface Signal Descriptions DMACK- DMA Acknowledge Dmarq DMA RequestIntrq Drive Interrupt IOCS16- Drive 16-bit I/ORESET- Drive Reset PDIAG- Passed DiagnosticsIordy I/O Channel Ready SD8 SD6 SD9 SD5 SD4SD3 SD2Drive Drive HostDIR Logical Interface GeneralBit Conventions EnvironmentSpinPoint V40 Product Manual Command Block Registers 2 I/O Register AddressControl Block Registers N N N A a aControl Block Register Descriptions Alternate Status Register 3F6hDrive Address Register 3F7h Device Control Register 3F6hCommand Block Register Descriptions Features Register 1F1hError Register 1F1h Data Register 1F0hCommand Register 1F7h Sector Count Register 1F2hCylinder High Register 1F5h Cylinder Low Register 1F4hStatus Register 1F7h BSY Drdy DWF DSC DRQ Corr IDX ERRAt Command Register Descriptions Command Parameter Used SpinPoint V40 Product Manual Execute Device Diagnostics 90h Check Power Mode 98h, E5hDownload Micro Code 92h Format Track 50h Flush Cache E7hIdentify Device ECh Word Content Description XxxxCapabilities Command set supported 95-128 0000h Reserved 129-159 Vendor specific 160-255 Idle Immediate 95h,E1h Idle 97h,E3hInitialize Device Parameters 91h Read Buffer E4h Read Long 22hwith retry, 23h without retryRead Multiple Command C4h Read Native Max Address F8h Read Sectors 20hwith retry, 21hwithout retryRecalibrate 1xh Read Verify Sectors 40hwith retry, 41hwithout retrySeek 7xh Set Features EFh ModeInputs LBANormal outputs BSY Drdy DRQ ERRDescription Set Multiple Mode C6h Sleep 99h, E6hStandby 96h,E2h Smart disable operation D9hSmart B0h Smart enable operations D8h Smart enable/disable attribute autosave D2hSmart execute off-line immediate D4h Smart read data D0h Byte DescriptionsValue Definition Off-line data collection capabilitySmart capability Smart read log sector D5hSmart return status DAh Smart save attribution value D3hStandby 96h, E2h Standby Immediate 94h, E0hWrite Buffer E8h Write DMA CAhWrite Multiple Command C5h Write Sectors 30hwith retry, 31hwithout retrySpinPoint V40 Product Manual Error Posting Reset ResponseProgramming Requirements Command Error Register Status Register BBKPower Conditions Sleep modeStandby mode Idle modeNormal mode PIO Data in Commands Protocol OverviewPIO Read Command PIO Data Out CommandsPIO Read Aborted Command PIO Write Command PIO Write Aborted CommandBSY=0 DRDY=1 BSY=1 BSY=0 DRQ=1 BSY=1 DRQ=0Non-Data Commands DMA Data Transfer Commands BSY=0 BSY=1 Aborted DMA Command Initialize DMA Reset DMA StatusBSY=1 BSY=0 Timing Register transfersDIOR-/DIOW Write PIO timing parameters Mode PIO data transfersAddr valid See note T1 t2 DIOR-/DIOW Multiword DMA data transfer DIOR-/DIOWMultiword DMA timing parameters Mode Ultra DMA data transfer Initiating an Ultra DMA data in burstUltra DMA data burst timing requirements 19Ultra DMA data burst timing requirementsSustained Ultra DMA data in burst 5Sustained Ultra DMA data in burstHost pausing an Ultra DMA data in burst 6Host pausing an Ultra DMA data in burstDevice terminating an Ultra DMA data in burst 7Device terminating an Ultra DMA data in burst 100Host terminating an Ultra DMA data in burst 8Host terminating an Ultra DMA data in burstInitiating an Ultra DMA data out burst 9Initiating an Ultra DMA data out burst 102Sustained Ultra DMA data out burst 10Sustained Ultra DMA data out burstDevice pausing an Ultra DMA data out burst 11Device pausing an Ultra DMA data out burst 104Host terminating an Ultra DMA data out burst 12Host terminating an Ultra DMA data out burstDevice terminating an Ultra DMA data out burst 13Device terminating an Ultra DMA data out burst 106Service And Repair Maintenance PrecautionsGeneral Information