JVC HR-XV1EK manual Remote control, How to install the batteries, Battery precautions, Dvd/Vcr

Page 9

 

 

Remote control

How to install the batteries

 

 

Use micro batteries type AA.

 

 

1 Open the battery compart-

2 Install two "AA" batteries (not

3 Replace the compartment

ment cover in the direction of

supplied), paying attention to the

cover.

the arrow.

polarity diagram in the battery

 

 

compartment.

 

Battery precautions

The precautions below should be followed when using batteries in this device:

1.Use only the size and type of batteries specified.

2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

3.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

5.Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.

Distance of Remote

Control Operation

approx.

5m

Effective angle: approx. 60°

Point the remote control directly at the remote sensor.

Change the custom code for remote control

If you operate this DVD/VCR with another JVC’s VCR simultaneously arranging them side by side, the both recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to other frequency (“ ”). Then you can operate only this DVD/VCR with this changed remote control.

When you purchased, the DVD/VCR and remote control have been set to the frequency-“ ”.

Example: Change frequency to

Remote control:

While holding VCR, press 2 (code: b) of Number keys.

(in case of code: A, press 1). Then press OK.

DVD/VCR:

In the POWER off mode, press and hold PLAY for more than 5 seconds. The current code (“A” or “b”) will appear on the display. Then press 3 on the remote control. The current code of the remote control will be transmitted to the unit and the unit will be adjusted to the transmitted code. Then the code will disappear after approx. 4 seconds.

NOTE:

•If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not be operated with this remote control.

•To reset to “A”, repeat above procedure. However press 1 instead of 2.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Digital Video Cassette Recorder USER’S GuideMoisture Condensation Safety PrecautionsSafety Precautions Do not block the recorder’s ventilation openings or holesAbove ALL Video Cassette Recorder FeaturesContents Parts and functions FrontRear Display window DisplayJVC TV Remote Control Remote controlHow to install the batteries Remote controlBattery precautions Change the custom code for remote controlConnections and Installation Connect a TV with the Scart socketVCR/DECODER Connection to a Satellite Receiver Playback connectionConnect to a TV with S-Video Output Satellite ReceiverPlayback connection Connecting the optical digital cableConnect to a Stereo Amplifier with Audio Output Connect to an AV Amplifier with built-in digital surroundTo skip a channel position CancelBBC ITVPress or to select On-screen Language SelectionLANGUAGE. Then Press OKClock Dayset Setting the Time and Date ManuallyCH4 Tuning the TV Stations ManuallyCH5 SatelliteSetting the Video Plus + Channel Number Guide CH Number keysGuide Channel Table Loading and Unloading a Cassette Tape Cassette tape playback Forward/Reverse picture search modeTo stop playback To rewind the tape or forward it rapidlySpecial playback/Playback sharpness/Skip Search Special playbackPlayback sharpness Repeat Playback To set the Repeat functionRepeat Counter Display Zero Return functionDISPLAY-button Video Index Search System Index SearchRecording several Index Marks To Stop Recording Recording a TV ProgrammeTo Stop Recording Temporarily TapeRecording a TV Programme Auto Rewind FeatureRecording with a Scart Lead To Display VCR operation StatusTo Extend the Recording Time Instant Timer Recording ITRTo stop the ITR Tape speed SPVideo Plus+ Recording Video Plus+ Recording To record with the PDC Programme Delivery Control SystemRecording period extension Press or to select the Timer REC SET. Then press OK Timer Recording ManuallyTimer Recording Manually Case of overlapping Timer programmesSet other START, END, CH, Speed as previous pages To confirm a Timer programme Confirmation/Cancellation of the Timer RecordingPress PROG. twice. All the timer programmes will appear To cancel a Timer programmeNicam stereo sound reception Nicam Stereo Recording and PlaybackNicam programmes are divided into 4 types as shown below To record Nicam programmes, select Nicam Auto as followsNicam Stereo Recording and Playback HiFi signal indicationPlayback HI-FIPress or to select VCR SETUP. Then press Audio MixingAudio MIX Connection with second Video recorder or Video camera Duplicating a Video TapeDuplicating a disc material onto a video tape Press AUX on the recording unit repeatedly until A3 appearsDisc Setup language can be selected Preparation Setting setup languagePress OPEN/CLOSE Playback procedureSpecial playback Zooming DVD Picture Signal Selection/ZoomingRepeat Playback Repeat PlaybackDVD Some discs may not work withMemory playback/Random playback Memory playbackRandom playback MP3 CD Information MP3 PlaybackLimitations on MP3 CD playback Limitations on displayChanging soundtrack language Cancel or OK buttonChanging Subtitles language Case of Video CD playbackChanging Angles Changing angles / Title selection / DVD menuTitle Selection DVD MenuParental control setting Parental controlDepending on the discs, the unit can- not limit playback Country/Area Parental controlTo change the parental lock level Follow steps 1Setting menu language English, French, GermanExample Press or to select Audio Language Setting audio soundtrack languageOK Enter Setting subtitle languagePress To select your Desired language, then press OK Enter No SubtitleSetting on Screen display Setting the aspect ratio of TV screenAudio Out Select Setting AudioDynamic Range Control Karaoke VocalPress SET UP Menu in the stop mode Setting OperationPause/Still Title StopSetting Screen Saver DVD only Setting BackgroundSelecting the sound enhancement E.A.M To exit the audio enhancement selection PressSetting initial setup/output sound conversion table You can install the initial system setting PreparationPCM Audio Status display of DiscVideo CD OFFTable of languages Problems and troubleshooting Symptoms Possible Solutions DVD/VCRVCR Video head cleaning Problems and troubleshooting / Video head cleaningSymptoms Possible Solutions Video head cloggingAccessories SpecificationsGeneral VCR section
Top Page Image Contents