Panasonic AJ-D250P Setup Menus, System menu, Setting Description of setting Superimposed Display

Page 27

Setup Menus

SYSTEM menu

		Item		Setting
					Description of setting
	No.	Superimposed	No.	Superimposed	Description of setting
		Superimposed		Superimposed
		display		display
		display		display

	00	SYSTEM H	0000	128	For adjusting the horizontal phase.
					This item enables the phase to be varied by up to ±1.5 µ.
			0255	127
	01	SC COARSE	0000	0	For coarsely adjusting the subcarrier phase.
			0001	90	This item enables the phase to be varied by selecting one of 4 positions at
			0002	180	90-degree increments.
			0003	270

	02	SC FINE	0000	128	For finely adjusting the subcarrier phase.
					This item enables the phase to be varied by up to 90 degrees.
					By using this item in tandem with SC COARSE, any setting up to 360
					degrees can be achieved.
			0255	127
	03	SCH COARSE	0000	0	For coarsely adjusting the SCH (Sub Carrier to Horizontal) phase.
			0001	90	This item enables the phase to be varied by selecting one of 4 positions at
			0002	180	90-degree increments.
			0003	270

	04	SCH FINE	0000	128	For finely adjusting the SCH (Sub Carrier to Horizontal) phase.
					This item enables the phase to be varied by up to 90 degrees.
					By using this item in tandem with SCH COARSE, any setting up to 360
					degrees can be achieved.
			0255	127
	05	VIDEO LEVEL	0000	128	For setting the video level.
					This item enables the video level to be varied by up to ±3 dB.
			0128	0
			0255	127

	06	SET UP LEVEL	0000	128	For setting the setup amount.
					This item enables the setup amount to be varied by up to 10 IRE.
			0128	0
			0255	127

	07	HUE	0000	128	For setting the hue.
					This item enables the hue to be varied by up to ±25 degrees.
			0128	0
			0255	127

	08	CHROMA LEVEL	0000	128	For setting the chroma level.
					This item enables the chroma level to be varied by up to ±3 dB.
			0128	0

0255

127

The underlining denotes the factory mode setting.

<Notes>

OItem numbers 05, 06, 07 and 08 are initialized only when ALL has been selected by the initialization operation.

OThe setting items are not initialized by the regular menu reset operation. The unit is shipped with the settings already adjusted.

27

Image 27

Contents VQT8188-2 S0699W3119 aFCC Note Contents Introduction FeaturesParts and Their Functions Front panelCounter display Cassette insertion slot Power switchLOCAL/MENU/REMOTE switch ? Input Select switchReset button Headphones jackVolume control Remote connectorConnector panel Audio in connectors Signal GND terminalVideo in connector REF Video in connectorTapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Check that the Stop lamp is lighted Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape OperationCheckpoint for Still Timer setting Stop modeRecording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Still picture playback Pause/record frame-to-frame continuityPlayback Cue/reviewFrame by frame advance Audio switchingSetting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points TCR 00 07 04 Time Codes and User’s BitTime codes User’s bitDown button Stop button Setting the time codeSetting the user’s bit Now follow the same procedure as for setting the time code00 07 04 Playing back the time code/user’s bitSuperimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settingsHow to display the Diag menu How to release the menu protect modeSystem menu Setup MenusSetting Description of setting Superimposed Display Underlining denotes the factory mode settingBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Noise may appear here at the joins in the edit points Audio editing functionsCutting FadingFirst Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters 3AH External interface specificationsSending format computer VTR $ Data formatExample Receiving format VTR computerOCounter control commands Command list$ List of commands OAudio control commandsOInput/output control commands ODisplay control commandsOEdit control commands OMedia operation control commandsOOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands$ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference Used as the reference $ Edit control commandsOWhen the CTL data is to be Menu item Setting Setting command$ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Parameters OIn the case of a Dvcpro Format tape Case of a Dvcpro format tapeCase of a DV format tape STX OSF ETXSTX OSR ETX OIn the case of CTL data $ Query control commandsCTL mode TC mode, UB mode, Remain modeFf = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter Addressf OSP StopAD AD AD AD AD AD9ADAADBADCADDADEADFCassette RF Video Tape Hard OBitmap table aRepeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETXOBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command OWhen CTL data is to be used $ Search control commandsBe stored in the memory OWhen the counter value is toOWhen the parameter value for OWhen the parameter value for Which the TC data serves asOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition tableInsert Pause Audio$ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error No Description Error MessagesEmergency Eject Procedure for removing the tape manually in an emergencyVideo Head Cleaning MaintenanceCondensation $ Digital video Specifications$ Input connectors $ Output connectors$ Digital audio Page Central Region Executive OfficeMid-Atlantic/New England Southeast Region