Panasonic AJ-D250P Parameter M1 HEX display M2 HEX display Bits supported, Switching data

Page 58

RS-232C

$Query control commands

Sends data of computer		Return data from VTR	Description of command


[STX] QIE [ETX]		[STX] IEVdata [ETX]	Queries the forced E-E output setting.
	data = m1m2
	m1 = 0	F: Designates the data of bit 7
		to bit 4.
	m2 = 0	F: Designates the data of bit 3
		to bit 0.

Parameter

m1 (HEX display)

m2 (HEX display)

Bits supported

BIT7

BIT6

BIT5

BIT4

BIT3

BIT2

BIT1

BIT0

Switching data

0

0

0

0

AUDIO CH1

AUDIO CH2

VIDEO

TC

[STX] QLH:m [ETX]

[STX] LHRdata [ETX]

Queries the current value of the hours meter.

Parameters

data = mhhhhh

m = D: Cumulative drum rotation

m = D: Drum

time

T: Capstan

T: Cumulative capstan rotation

hhhhh = 00000

99999:

time

Cumulative rotation time

No parameter:

OWith no parameter

Cumulative drum rotation

The drum’s cumulative rotation time

time (4 digits)

is returned as a 4-digit value.

data = hhhh

hhhh = 0000

9999:

Cumulative rotation time

[STX] QOT [ETX]

[STX] OTEm [ETX]

Queries whether to set to the E-E output or V-V output

m = E:

when the VTR is in the STOP mode, FF mode or REW

E-E (Electric modulation to Electric

mode.

play back)

m = T:

V-V (VTR to VTR recording)

58

Image 58

Contents S0699W3119 a VQT8188-2FCC Note Contents Features IntroductionFront panel Parts and Their FunctionsCounter display ? Input Select switch Power switchLOCAL/MENU/REMOTE switch Cassette insertion slotRemote connector Headphones jackVolume control Reset buttonConnector panel REF Video in connector Signal GND terminalVideo in connector Audio in connectorsTape Description TapesCassette Checkpoints for consumer-use DV tape playback Operation Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape Check that the Stop lamp is lightedStop mode Checkpoint for Still Timer settingPress the Play button while holding down the REC button RecordingPress the Stop button to end the recording Cue/review Pause/record frame-to-frame continuityPlayback Still picture playbackAudio switching Frame by frame advanceSelect TC or CTL using the Counter button. Note Setting the Begin and END points Menu modeRepeat playback Setting the repeat playback mode Setting the Begin and END points Front panelDisplaying the Begin and END points User’s bit Time Codes and User’s BitTime codes TCR 00 07 04Now follow the same procedure as for setting the time code Setting the time codeSetting the user’s bit Down button Stop buttonPlaying back the time code/user’s bit 00 07 04Display position Superimposed ScreensCharacters displayed Superimpose Screens How to perform the settings using the on-screen menus Setup Initial SettingsHow to restore the factory settings How to set the user default settings How to load the user default settings How to initiate the menu protect modeHow to release the menu protect mode How to display the Diag menuUnderlining denotes the factory mode setting Setup MenusSetting Description of setting Superimposed Display System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Preparation EditingOperation Fading Audio editing functionsCutting Noise may appear here at the joins in the edit pointsFirst edit for assemble editing First Edit Function Preparing the editing tapeFirst edit for insert editing RS-232C Interface specificationsCommunication parameters $ Data format External interface specificationsSending format computer VTR 3AHReceiving format VTR computer ExampleOAudio control commands Command list$ List of commands OCounter control commandsOMedia operation control commands ODisplay control commandsOEdit control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands$ Counter control commands $ Audio control commandsParameters Sets the signal to be regenerated when the TCG time code CTL data reference $ Display control commandsTC data reference Menu item Setting Setting command $ Edit control commandsOWhen the CTL data is to be Used as the reference$ Input/output control commands $ Media operation control commandsM1 HEX display M2 HEX display STX OBF ETX $ Operation control commandsSTX ORC ETX STX OSF ETX Case of a Dvcpro format tapeCase of a DV format tape Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX TC mode, UB mode, Remain mode $ Query control commandsCTL mode OIn the case of CTL dataFf = Frames Rewind Play Play Pause STX QHR ETX Auto Back OFF STX QHC ETXRewind Eject Parameter M1 HEX display M2 HEX display Bits supported Switching dataOWith no parameter AD9ADAADBADCADDADEADF OSP StopAD AD AD AD AD AddressfOBitmap table a Cassette RF Video Tape HardACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETXOBitmap table B Reference OWhen CTL data is to be used asVideo Option STX QVM ETX OParameter setting normal $ Communication control commandsOParameter setting no completion command $ Search control commands OWhen CTL data is to be usedOWhen the parameter value for Which the TC data serves as OWhen the counter value is toOWhen the parameter value for Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC PauseAudio Insert Pause$ Send command intervals $ Send commands and data returned fromCheckpoints for RS-232C communication Error Messages Error No DescriptionProcedure for removing the tape manually in an emergency Emergency EjectMaintenance Video Head CleaningCondensation $ Output connectors Specifications$ Input connectors $ Digital video$ Digital audio Page Southeast Region Executive OfficeMid-Atlantic/New England Central Region