Panasonic AJ-D250P AC in socket, Signal GND terminal, Fan motor, Grip, Video in connector

Page 9

Parts and Their Functions

Connector panel

1AC IN socket

Plug one end of the unit’s power cord into this power socket.

2SIGNAL GND terminal

In order to reduce noise, connect this terminal to the signal grounding terminal on one of the devices to which the unit is connected. This is not a safety ground.

3Fan motor

This motor is used to cool the unit.

4Grip

This grip is fitted on the side panel. When operating the unit, however, place the unit flat on its bottom surface.

5S-VIDEO IN connector

The S-VIDEO video signals are supplied to this connector.

6VIDEO IN connector

The analog video signals are supplied to this connector.

7REF VIDEO IN connector

This is connected to the reference video signal when the unit is to be synchronized with the reference sync signals of an external unit during playback.

8AUDIO IN connectors

The analog audio signals are supplied to this connector.

9S-VIDEO OUT connector

The S-VIDEO video signals are output from this connector.

:VIDEO OUT connector

The analog video signals are output from this connector.

;MONITOR OUT connector

The video monitor signals are output from this connector. Superimposed video signals can be output.

<AUDIO 1 OUT connectors

The analog audio signals are output from this connector.

=AUDIO 2 OUT connectors

The analog audio signals are output from this connector.

>RS-232C connector

Editing operations can be conducted speedily and efficiently by connecting the RS-232C remote control (AJ-A250 - available as an optional accessory) to this connector. Various operations can be performed from a computer by using the RS-232C cable which is available as an optional accessory.

	INPUT		REF
	S-VIDEO	VIDEO	VIDEO
	S-VIDEO
			AUDIO
			CH1	CH2
	OUTPUT		VIDEO
RS-	S-VIDEO	VIDEO	MONIT
232C
RS-232C	CH1	CH2	CH1	CH2
	AUDIO 1		AUDIO 2		AC IN
					AC IN

connector

SIGNAL

GND

9

Image 9

Contents VQT8188-2 S0699W3119 aFCC Note Contents Introduction FeaturesParts and Their Functions Front panelCounter display LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slotVolume control Headphones jackRemote connector Reset buttonConnector panel Video in connector Signal GND terminalREF Video in connector Audio in connectorsTapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lightedCheckpoint for Still Timer setting Stop modeRecording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Playback Pause/record frame-to-frame continuityCue/review Still picture playbackFrame by frame advance Audio switchingSetting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button00 07 04 Playing back the time code/user’s bitSuperimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settingsHow to display the Diag menu How to release the menu protect modeSetting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit pointsFirst Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters Sending format computer VTR External interface specifications$ Data format 3AHExample Receiving format VTR computer$ List of commands Command listOAudio control commands OCounter control commandsOEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands$ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference$ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL dataFf = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF AddressfCassette RF Video Tape Hard OBitmap table aRepeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETXOBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command OWhen CTL data is to be used $ Search control commandsOWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition tableInsert Pause Audio$ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error No Description Error MessagesEmergency Eject Procedure for removing the tape manually in an emergencyVideo Head Cleaning MaintenanceCondensation $ Input connectors Specifications$ Output connectors $ Digital video$ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region