Panasonic AJ-D250P Data = wghmmssff Still mode is established upon completion

Page 69

RS-232C

$Search control commands

Sends data of computer			Return data from VTR		Description of command


	[STX] SRS:data [ETX]		[STX] SRS [ETX]	Searches the counter value which was designated by the
Parameters				parameter.
data = wghmmssff				The STILL mode is established upon completion of the
OWhen CTL data is to be used				search.
as the reference				If the designated position is an illegal position (the target
w = L: CTL data reference				position does not exist), error code ER122 will be returned
g = Blank: With a positive value				from the VTR, which is then set to the STOP mode.
– sign: With a negative value				When the OSP (STOP) command or OEJ (tape EJECT)
h =	0	9: Hours		command is issued during operation, error code ER123 is
mm = 00		59: Minutes		returned from the VTR.
ss =	00	59: Seconds		If the VTR’s operation mode has been changed by
ff =	00	29: Frames		operating the controls on its front panel, error code ER121
OWhen TC data is to be used as				will be returned from the VTR.
the reference				If the tape end position is reached during operation, error
w =	S: TC data reference			code ER120 will be returned from the VTR.
gh =	00	23: Hours		When data differing from the data used as the reference
mm = 00		59: Minutes		has been sent, error code ER001 will be returned from the
ss =	00	59: Seconds		VTR.
ff =	00	29: Frames		<Note>
				This command is ignored while a search control command
				is being processed and in any of the following modes.

					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE


	[STX] SUB:data [ETX]		[STX] SUB [ETX]	Searches the start position of the user’s bit which was
Parameters				designated by the parameter.
data = uuuuuuuu:d				The STILL mode is established upon completion of the
u = 0 F: User’s bit value				search.
(“ ” is designated for a user’s bit				The search is enabled when the same user’s bit value
value which is not going to be				continues for at least 5 seconds.
searched)				When the OSP (STOP) command or OEJ (tape EJECT)
d = F: Forward direction				command is issued during operation, error code ER123 is
	R: Reverse direction			returned from the VTR.
				If the VTR’s operation mode has been changed by
				operating the controls on its front panel, error code ER121
				will be returned from the VTR.
				If the tape end position is reached during operation, error
				code ER120 will be returned from the VTR.
				<Note>
				This command is ignored while a search control command
				is being processed and in any of the following modes.

					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE

69

Image 69

Contents VQT8188-2 S0699W3119 aFCC Note Contents Introduction FeaturesParts and Their Functions Front panelCounter display LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slotVolume control Headphones jackRemote connector Reset buttonConnector panel Video in connector Signal GND terminalREF Video in connector Audio in connectorsTapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lightedCheckpoint for Still Timer setting Stop modeRecording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Playback Pause/record frame-to-frame continuityCue/review Still picture playbackFrame by frame advance Audio switchingSetting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button00 07 04 Playing back the time code/user’s bitSuperimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settingsHow to display the Diag menu How to release the menu protect modeSetting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit pointsFirst Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters Sending format computer VTR External interface specifications$ Data format 3AHExample Receiving format VTR computer$ List of commands Command listOAudio control commands OCounter control commandsOEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands$ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference$ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL dataFf = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF AddressfCassette RF Video Tape Hard OBitmap table aRepeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETXOBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command OWhen CTL data is to be used $ Search control commandsOWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition tableInsert Pause Audio$ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error No Description Error MessagesEmergency Eject Procedure for removing the tape manually in an emergencyVideo Head Cleaning MaintenanceCondensation $ Input connectors Specifications$ Output connectors $ Digital video$ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region