Panasonic AJ-D250P operating instructions Searches the counter value at the time when the command

Page 68

RS-232C

$Search control commands

Sends data of computer			Return data from VTR		Description of command


	[STX] SMS [ETX]		[STX] SMS [ETX]	Searches the counter value at the time when the command
				stored in the memory was received.
				The STILL mode is established upon completion of the
				search.
				If the designated position is an illegal position (the target
				position does not exist), error code ER122 will be returned
				from the VTR which is then set to the STOP mode.
				When the OSP (STOP) command or OEJ (tape EJECT)
				command is issued during operation, error code ER123 is
				returned from the VTR.
				If the VTR’s operation mode has been changed by
				operating the controls on its front panel, error code ER121
				will be returned from the VTR.
				If the tape end position is reached during operation, error
				code ER120 will be returned from the VTR.
				When data differing from the data used as the reference
				has been sent or when the counter value has not been
				stored in the memory, error code ER001 will be returned
				from the VTR.
				<Note>
				This command is ignored while a search control command
				is being processed and in any of the following modes.

					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE


	[STX] SPT:data [ETX]		[STX] SPT [ETX]	Plays the tape to the position which was designated by the
Parameters				parameter.
data = ghmmssff				The VTR is set to the STILL mode upon completion of
OWhen CTL data is to be used				playback.
as the reference				If the designated position is before the current position, the
g = Blank: With a positive value				tape is not played back, and the VTR is set to the STILL
– sign: With a negative value				mode.
h =	0	9: Hours		When the OSP (STOP) command or OEJ (tape EJECT)
mm = 00		59: Minutes		command is issued during operation, error code ER123 is
ss =	00	59: Seconds		returned from the VTR.
ff =	00	29: Frames		If the VTR’s operation mode has been changed by
OWhen TC data is to be used as				operating the controls on its front panel, error code ER121
the reference				will be returned from the VTR.
gh =	00	23: Hours		If the tape end position is reached during operation, error
mm = 00		59: Minutes		code ER120 will be returned from the VTR.
ss =	00	59: Seconds		<Note>
ff =	00	29: Frames		This command is ignored while a search control command
				is being processed and in any of the following modes.

					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE

68

Image 68

Contents S0699W3119 a VQT8188-2FCC Note Contents Features IntroductionCounter display Parts and Their FunctionsFront panel Power switch LOCAL/MENU/REMOTE switch? Input Select switch Cassette insertion slotHeadphones jack Volume controlRemote connector Reset buttonConnector panel Signal GND terminal Video in connectorREF Video in connector Audio in connectorsCassette Checkpoints for consumer-use DV tape playback TapesTape Description Turning on the power/inserting a cassette Turn on the unit’s power Insert the cassette tapeOperation Check that the Stop lamp is lightedStop mode Checkpoint for Still Timer settingPress the Stop button to end the recording RecordingPress the Play button while holding down the REC button Pause/record frame-to-frame continuity PlaybackCue/review Still picture playbackAudio switching Frame by frame advanceRepeat playback Setting the Begin and END points Menu modeSelect TC or CTL using the Counter button. Note Displaying the Begin and END points Setting the Begin and END points Front panelSetting the repeat playback mode Time Codes and User’s Bit Time codesUser’s bit TCR 00 07 04Setting the time code Setting the user’s bitNow follow the same procedure as for setting the time code Down button Stop buttonPlaying back the time code/user’s bit 00 07 04Characters displayed Superimposed ScreensDisplay position Superimpose Screens How to restore the factory settings Setup Initial SettingsHow to perform the settings using the on-screen menus How to set the user default settings How to load the user default settings How to initiate the menu protect modeHow to release the menu protect mode How to display the Diag menuSetup Menus Setting Description of setting Superimposed DisplayUnderlining denotes the factory mode setting System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Operation EditingPreparation Audio editing functions CuttingFading Noise may appear here at the joins in the edit pointsFirst edit for insert editing First Edit Function Preparing the editing tapeFirst edit for assemble editing Communication parameters Interface specificationsRS-232C External interface specifications Sending format computer VTR$ Data format 3AHReceiving format VTR computer ExampleCommand list $ List of commandsOAudio control commands OCounter control commandsODisplay control commands OEdit control commandsOMedia operation control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commandsParameters $ Audio control commands$ Counter control commands Sets the signal to be regenerated when the TCG time code TC data reference $ Display control commandsCTL data reference $ Edit control commands OWhen the CTL data is to beMenu item Setting Setting command Used as the referenceM1 HEX display M2 HEX display $ Media operation control commands$ Input/output control commands STX ORC ETX $ Operation control commandsSTX OBF ETX Case of a Dvcpro format tape Case of a DV format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX $ Query control commands CTL modeTC mode, UB mode, Remain mode OIn the case of CTL dataFf = Frames Rewind Eject Auto Back OFF STX QHC ETXRewind Play Play Pause STX QHR ETX OWith no parameter Switching dataParameter M1 HEX display M2 HEX display Bits supported OSP Stop AD AD AD AD ADAD9ADAADBADCADDADEADF AddressfOBitmap table a Cassette RF Video Tape HardACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETXOBitmap table B Video Option STX QVM ETX OWhen CTL data is to be used asReference OParameter setting no completion command $ Communication control commandsOParameter setting normal $ Search control commands OWhen CTL data is to be usedOWhen the counter value is to OWhen the parameter value forOWhen the parameter value for Which the TC data serves as Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC PauseAudio Insert PauseCheckpoints for RS-232C communication $ Send commands and data returned from$ Send command intervals Error Messages Error No DescriptionProcedure for removing the tape manually in an emergency Emergency EjectCondensation Video Head CleaningMaintenance Specifications $ Input connectors$ Output connectors $ Digital video$ Digital audio Page Executive Office Mid-Atlantic/New EnglandSoutheast Region Central Region