Panasonic AJ-D250P operating instructions OSearches control commands, OTimer control commands

Page 46

RS-232C

OSearches control commands

	Sends data of computer	Return data from VTR	Description of command


	[STX] SCP:data [ETX]	[STX] SCP [ETX]	Searches the counter value and play.

	[STX] SCS:data [ETX]	[STX] SCS [ETX]	Searches the counter value and sets to still picture (same
	[STX] SCS:data [ETX]	[STX] SCS [ETX]	as SRS).
			as SRS).

	[STX] SMI:data [ETX]	[STX] SMI [ETX]	Sets the memory search data.

	[STX] SMM:m [ETX]	[STX] SMM [ETX]	Sets the memory mode.

	[STX] SMP:data [ETX]	[STX] SMP [ETX]	Specifies the repeat position.

	[STX] SMS [ETX]	[STX] SMS [ETX]	Searches the memory data.

	[STX] SPT:data [ETX]	[STX] SPT [ETX]	Plays the tape back to the designated position (same as
	[STX] SPT:data [ETX]	[STX] SPT [ETX]	OPT).
			OPT).

	[STX] SRS:data [ETX]	[STX] SRS [ETX]	Searches the counter value and sets to still picture (same
	[STX] SRS:data [ETX]	[STX] SRS [ETX]	as SCS).
			as SCS).

	[STX] SUB:data [ETX]	[STX] SUB [ETX]	Searches the user’s bit.

OTimer control commands

Sends data of computer

Return data from VTR

Description of command

[STX] TST:data [ETX]

[STX] TST [ETX]

Sets the standby off timer.

46

Image 46

Contents S0699W3119 a VQT8188-2FCC Note Contents Features IntroductionFront panel Parts and Their FunctionsCounter display ? Input Select switch Power switchLOCAL/MENU/REMOTE switch Cassette insertion slotRemote connector Headphones jackVolume control Reset buttonConnector panel REF Video in connector Signal GND terminalVideo in connector Audio in connectorsTape Description TapesCassette Checkpoints for consumer-use DV tape playback Operation Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape Check that the Stop lamp is lightedStop mode Checkpoint for Still Timer settingPress the Play button while holding down the REC button RecordingPress the Stop button to end the recording Cue/review Pause/record frame-to-frame continuityPlayback Still picture playbackAudio switching Frame by frame advanceSelect TC or CTL using the Counter button. Note Setting the Begin and END points Menu modeRepeat playback Setting the repeat playback mode Setting the Begin and END points Front panelDisplaying the Begin and END points User’s bit Time Codes and User’s BitTime codes TCR 00 07 04Now follow the same procedure as for setting the time code Setting the time codeSetting the user’s bit Down button Stop buttonPlaying back the time code/user’s bit 00 07 04Display position Superimposed ScreensCharacters displayed Superimpose Screens How to perform the settings using the on-screen menus Setup Initial SettingsHow to restore the factory settings How to set the user default settings How to load the user default settings How to initiate the menu protect modeHow to release the menu protect mode How to display the Diag menuUnderlining denotes the factory mode setting Setup MenusSetting Description of setting Superimposed Display System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Preparation EditingOperation Fading Audio editing functionsCutting Noise may appear here at the joins in the edit pointsFirst edit for assemble editing First Edit Function Preparing the editing tapeFirst edit for insert editing RS-232C Interface specificationsCommunication parameters $ Data format External interface specificationsSending format computer VTR 3AHReceiving format VTR computer ExampleOAudio control commands Command list$ List of commands OCounter control commandsOMedia operation control commands ODisplay control commandsOEdit control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands$ Counter control commands $ Audio control commandsParameters Sets the signal to be regenerated when the TCG time code CTL data reference $ Display control commandsTC data reference Menu item Setting Setting command $ Edit control commandsOWhen the CTL data is to be Used as the reference$ Input/output control commands $ Media operation control commandsM1 HEX display M2 HEX display STX OBF ETX $ Operation control commandsSTX ORC ETX STX OSF ETX Case of a Dvcpro format tapeCase of a DV format tape Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX TC mode, UB mode, Remain mode $ Query control commandsCTL mode OIn the case of CTL dataFf = Frames Rewind Play Play Pause STX QHR ETX Auto Back OFF STX QHC ETXRewind Eject Parameter M1 HEX display M2 HEX display Bits supported Switching dataOWith no parameter AD9ADAADBADCADDADEADF OSP StopAD AD AD AD AD AddressfOBitmap table a Cassette RF Video Tape HardACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETXOBitmap table B Reference OWhen CTL data is to be used asVideo Option STX QVM ETX OParameter setting normal $ Communication control commandsOParameter setting no completion command $ Search control commands OWhen CTL data is to be usedOWhen the parameter value for Which the TC data serves as OWhen the counter value is toOWhen the parameter value for Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC PauseAudio Insert Pause$ Send command intervals $ Send commands and data returned fromCheckpoints for RS-232C communication Error Messages Error No DescriptionProcedure for removing the tape manually in an emergency Emergency EjectMaintenance Video Head CleaningCondensation $ Output connectors Specifications$ Input connectors $ Digital video$ Digital audio Page Southeast Region Executive OfficeMid-Atlantic/New England Central Region