Panasonic AJ-D250P $ Edit control commands, OWhen the CTL data is to be, Used as the reference

RS-232C

$Edit control commands

Sends data of computer			Return data from VTR		Description of command
	[STX] EAB:m [ETX]		[STX] EAB [ETX]	Sets whether auto back recording is to be performed to
Parameters				ensure frame to frame continuity.
m = N: AUTO BACK ON				<Note>
F: AUTO BACK OFF				This command is ignored while a search control command
				is being processed and during auto back.
	[STX] EAD:m [ETX]		[STX] EAD [ETX]	Sets the VTR to the AUDIO INSERT PAUSE mode.
Parameters				When the VTR is in the VIDEO INSERT PAUSE mode, the
m = 0: CH1 & CH2				command sets it to the AUDIO/VIDEO INSERT PAUSE
1: CH1				mode. When it is in the REC INHIBIT mode, error code
2: CH2				ER001 is returned from the VTR and the VTR is set to the
No parameter: CH1 & CH2				STOP mode.
				<Note>
				This command can be accepted when the VTR is in the
				PLAY PAUSE mode or STILL mode.
	[STX] EIN [ETX]		[STX] EIN [ETX]	Sets the VTR to the VIDEO INSERT PAUSE mode.
				When the VTR is in the AUDIO INSERT PAUSE mode, the
				command sets it to the AUDIO/VIDEO INSERT PAUSE
				mode. When it is in the REC INHIBIT mode, error code
				ER001 is returned from the VTR and the VTR is set to the
				STOP mode.
				<Note>
				This command can be accepted when the VTR is in the
				PLAY PAUSE mode or STILL mode.
	[STX] EFE:data [ETX]		[STX] EFE [ETX]	Initiates first edit (recording to prepare the tape to be used
Parameters				for editing).
data = wghmmssff				In order to conduct editing with the position designated by
w = M: Mode for recording for 26				the parameter as the reference point for editing, TC or CTL
	seconds			is preset using the value 23 seconds before the reference
E: Mode for recording as far				point, and the black burst video signal and muted audio
	as the tape end			signals are recorded for 26 seconds or until the tape end.
ghmmssff = Reference point during				If the OSP (STOP) command has been issued during
		editing (recording start		operation, error code ER123 will be returned from the VTR
		point)		which is then set to the STOP mode.
OWhen the CTL data is to be				If the VTR’s operation mode has been changed by
used as the reference				operating the controls on its front panel, error code ER121
g = Blank: With a positive value				will be returned from the VTR which is then set to the STOP
– sign: With a negative value				mode.
h =	0	9: Hours		If the tape end position is reached during operation, error
mm = 00		59: Minutes		code ER120 will be returned from the VTR which is then set
ss =	00	59: Seconds		to the STOP mode.
ff =	00	29: Frames		<Note>
OWhen the TC data is to be used				This command is ignored while a search control command
as the reference				is being processed and in any of the following modes.
gh =	00	23: Hours
					EJECT, REC, REC PAUSE, INSERT, INSERT PAUSE
mm = 00		59: Minutes
ss =	00	59: Seconds
ff =	00	29: Frames

<Note>

Make the menu item changes listed below when performing insert editing or assemble editing. If these changes are not made, the editing operations may not be conducted properly.

Menu item	Setting	Setting command
AUTO BACK	ON	EAB:N
TC MODE	I-REG	CTM:2
TCG REGEN	TC & UB	CRN:0
MEMORY MODE	OFF	SMM:F
STILL TIMER	2 min	TST:0200

50