Panasonic AJ-D250P OWhen the counter value is to, Be stored in the memory, Memory

Page 66

RS-232C

$Search control commands

Sends data of computer			Return data from VTR	Description of command


[STX] SMI:data [ETX]			[STX] SMI [ETX]	Stores the counter value and parameter value in the
Parameters				memory at the time when this command is received.
data = wwghmmssff				<Note>
OWhen the counter value is to				This command is ignored while a search control command
be stored in the memory				is being processed.
ww = LC: CTL data reference
	SC: TC data reference
“ghmmssff” is omitted.
OWhen the parameter value for
which the CTL data serves as
the reference is to be stored in
the memory
ww = LP: CTL data reference
g = Blank: With a positive value
– sign: With a negative value
h =	0	9: Hours
mm = 00		59: Minutes
ss =	00	59: Seconds
ff =	00	29: Frames
OWhen the parameter value for
which the TC data serves as
the reference is to be stored in
the memory
ww =	SP: TC data reference
gh =	00	23: Hours
mm = 00		59: Minutes
ss =	00	59: Seconds
ff =	00	29: Frames

	[STX] SMM:m [ETX]		[STX] SMM [ETX]	Sets the memory mode.
Parameters				<Note>
m = S: MEMORY STOP				This command is ignored while a search control command
O: REPEAT ONE TIME				is being processed.
A: CONTINUE
F: OFF

66

Image 66

Contents S0699W3119 a VQT8188-2FCC Note Contents Features IntroductionParts and Their Functions Front panelCounter display ? Input Select switch Power switchLOCAL/MENU/REMOTE switch Cassette insertion slotRemote connector Headphones jackVolume control Reset buttonConnector panel REF Video in connector Signal GND terminalVideo in connector Audio in connectorsTapes Tape DescriptionCassette Checkpoints for consumer-use DV tape playback Operation Turning on the power/inserting a cassetteTurn on the unit’s power Insert the cassette tape Check that the Stop lamp is lightedStop mode Checkpoint for Still Timer settingRecording Press the Play button while holding down the REC buttonPress the Stop button to end the recording Cue/review Pause/record frame-to-frame continuityPlayback Still picture playbackAudio switching Frame by frame advanceSetting the Begin and END points Menu mode Select TC or CTL using the Counter button. NoteRepeat playback Setting the Begin and END points Front panel Setting the repeat playback modeDisplaying the Begin and END points User’s bit Time Codes and User’s BitTime codes TCR 00 07 04Now follow the same procedure as for setting the time code Setting the time codeSetting the user’s bit Down button Stop buttonPlaying back the time code/user’s bit 00 07 04Superimposed Screens Display positionCharacters displayed Superimpose Screens Setup Initial Settings How to perform the settings using the on-screen menusHow to restore the factory settings How to set the user default settings How to load the user default settings How to initiate the menu protect modeHow to release the menu protect mode How to display the Diag menuUnderlining denotes the factory mode setting Setup MenusSetting Description of setting Superimposed Display System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Editing PreparationOperation Fading Audio editing functionsCutting Noise may appear here at the joins in the edit pointsFirst Edit Function Preparing the editing tape First edit for assemble editingFirst edit for insert editing Interface specifications RS-232CCommunication parameters $ Data format External interface specificationsSending format computer VTR 3AHReceiving format VTR computer ExampleOAudio control commands Command list$ List of commands OCounter control commandsOMedia operation control commands ODisplay control commandsOEdit control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OSearches control commands OTimer control commands$ Audio control commands $ Counter control commandsParameters Sets the signal to be regenerated when the TCG time code $ Display control commands CTL data referenceTC data reference Menu item Setting Setting command $ Edit control commandsOWhen the CTL data is to be Used as the reference$ Media operation control commands $ Input/output control commandsM1 HEX display M2 HEX display $ Operation control commands STX OBF ETXSTX ORC ETX STX OSF ETX Case of a Dvcpro format tapeCase of a DV format tape Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX TC mode, UB mode, Remain mode $ Query control commandsCTL mode OIn the case of CTL dataFf = Frames Auto Back OFF STX QHC ETX Rewind Play Play Pause STX QHR ETXRewind Eject Switching data Parameter M1 HEX display M2 HEX display Bits supportedOWith no parameter AD9ADAADBADCADDADEADF OSP StopAD AD AD AD AD AddressfOBitmap table a Cassette RF Video Tape HardACK OFF STX QRS ETX Repeat ONE Time Continue OFF STX QSY ETXOBitmap table B OWhen CTL data is to be used as ReferenceVideo Option STX QVM ETX $ Communication control commands OParameter setting normalOParameter setting no completion command $ Search control commands OWhen CTL data is to be usedOWhen the parameter value for Which the TC data serves as OWhen the counter value is toOWhen the parameter value for Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands $ Mode transition table Play REC PauseAudio Insert Pause$ Send commands and data returned from $ Send command intervalsCheckpoints for RS-232C communication Error Messages Error No DescriptionProcedure for removing the tape manually in an emergency Emergency EjectVideo Head Cleaning MaintenanceCondensation $ Output connectors Specifications$ Input connectors $ Digital video$ Digital audio Page Southeast Region Executive OfficeMid-Atlantic/New England Central Region