Panasonic AJ-D250P First Edit Function Preparing the editing tape, First edit for insert editing

Page 37

First Edit Function (Preparing the editing tape)

The CTL (control) signal must be recorded ahead of time onto the editing tape. The method used to record it differs depending on whether assemble editing or insert editing is to be performed.

First edit for assemble editing

In the case of a tape for assemble editing, the CTL signal is recorded at the beginning of where the recording is to be commenced.

Position where CTL signal recording starts

3 sec.

Direction of tape travel

CTL signal recording

–23 sec. position

0 sec. position

First edit for insert editing

In the case of a tape for insert editing, the CTL signal is recorded from the beginning of where the recording is to be commenced to the end.

The “E-00” servo lock error appears on the tape counter when insert editing is performed for a tape on which the CTL signal has not been recorded.

When insert editing is performed, the CTL signal must be recorded ahead of time.

<Note>

When first edit is to be performed, operation can be conducted by connecting the RS-232C remote control (AJ-A250), which is available as an optional accessory. However, control using the RS-232C interface (EFE command) can also be exercised from a computer.

(See page 50)

37

Image 37
Contents VQT8188-2 S0699W3119 aFCC Note Contents Introduction FeaturesFront panel Parts and Their FunctionsCounter display LOCAL/MENU/REMOTE switch Power switch? Input Select switch Cassette insertion slotVolume control Headphones jackRemote connector Reset buttonConnector panel Video in connector Signal GND terminalREF Video in connector Audio in connectorsTape Description TapesCassette Checkpoints for consumer-use DV tape playback Turn on the unit’s power Insert the cassette tape Turning on the power/inserting a cassetteOperation Check that the Stop lamp is lightedCheckpoint for Still Timer setting Stop modePress the Play button while holding down the REC button RecordingPress the Stop button to end the recording Playback Pause/record frame-to-frame continuityCue/review Still picture playbackFrame by frame advance Audio switchingSelect TC or CTL using the Counter button. Note Setting the Begin and END points Menu modeRepeat playback Setting the repeat playback mode Setting the Begin and END points Front panelDisplaying the Begin and END points Time codes Time Codes and User’s BitUser’s bit TCR 00 07 04Setting the user’s bit Setting the time codeNow follow the same procedure as for setting the time code Down button Stop button00 07 04 Playing back the time code/user’s bitDisplay position Superimposed ScreensCharacters displayed Superimpose Screens How to perform the settings using the on-screen menus Setup Initial SettingsHow to restore the factory settings How to set the user default settings How to initiate the menu protect mode How to load the user default settingsHow to display the Diag menu How to release the menu protect modeSetting Description of setting Superimposed Display Setup MenusUnderlining denotes the factory mode setting System menuBasic menu Operation menu Interface menu Tape Protect menu Time Code menu Video menu Audio menu Preparation EditingOperation Cutting Audio editing functionsFading Noise may appear here at the joins in the edit pointsFirst edit for assemble editing First Edit Function Preparing the editing tapeFirst edit for insert editing RS-232C Interface specificationsCommunication parameters Sending format computer VTR External interface specifications$ Data format 3AHExample Receiving format VTR computer$ List of commands Command listOAudio control commands OCounter control commandsOEdit control commands ODisplay control commandsOMedia operation control commands OInput/output control commandsOOperation control commands OQuery control commands OCommunication control commands OTimer control commands OSearches control commands$ Counter control commands $ Audio control commandsParameters Sets the signal to be regenerated when the TCG time code CTL data reference $ Display control commandsTC data reference OWhen the CTL data is to be $ Edit control commandsMenu item Setting Setting command Used as the reference$ Input/output control commands $ Media operation control commandsM1 HEX display M2 HEX display STX OBF ETX $ Operation control commandsSTX ORC ETX Case of a DV format tape Case of a Dvcpro format tapeSTX OSF ETX Parameters OIn the case of a Dvcpro Format tapeSTX OSR ETX CTL mode $ Query control commandsTC mode, UB mode, Remain mode OIn the case of CTL dataFf = Frames Rewind Play Play Pause STX QHR ETX Auto Back OFF STX QHC ETXRewind Eject Parameter M1 HEX display M2 HEX display Bits supported Switching dataOWith no parameter AD AD AD AD AD OSP StopAD9ADAADBADCADDADEADF AddressfCassette RF Video Tape Hard OBitmap table aRepeat ONE Time Continue OFF STX QSY ETX ACK OFF STX QRS ETXOBitmap table B Reference OWhen CTL data is to be used asVideo Option STX QVM ETX OParameter setting normal $ Communication control commandsOParameter setting no completion command OWhen CTL data is to be used $ Search control commandsOWhen the parameter value for OWhen the counter value is toOWhen the parameter value for Which the TC data serves as Be stored in the memoryOWhen the designated position is not to be entered Searches the counter value at the time when the command Data = wghmmssff Still mode is established upon completion $ Timer control commands Play REC Pause $ Mode transition tableInsert Pause Audio$ Send command intervals $ Send commands and data returned fromCheckpoints for RS-232C communication Error No Description Error MessagesEmergency Eject Procedure for removing the tape manually in an emergencyMaintenance Video Head CleaningCondensation $ Input connectors Specifications$ Output connectors $ Digital video$ Digital audio Page Mid-Atlantic/New England Executive OfficeSoutheast Region Central Region