JVC HR-J313EU Link Functions, Li Nk, NexTView Link, TV Auto Power On, VCR Auto Standby Direct Rec

Page 11

T-VLINK

EN11

T-V Link

Functions

When you connect the recorder and your TV via fully-wired 21-pin SCART cable (☞ pg. 3), the following functions are available. You can use these functions only with the TV offering T-V Link, etc.*

For details, refer to the instruction manual for your TV.

*Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NEXTVIEWLINK via fully- wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

NexTView Link

You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the recorder.

For details, refer to the instruction manual for your TV.

TV Auto Power On

You can turn on the TV and set it to video mode automatically whenever you play a tape.

For details, refer to the instruction manual for your TV.

VCR Auto Standby

You can use your TV's remote control to turn off the recorder. For details, refer to the instruction manual for your TV.

Direct Rec

You can start recording the programme that you are watching on your TV with simple operation. Press and hold RECORD and press PLAY on the remote control, or press RECORD on the recorder.

Follow the procedure below to use this function.

TURN ON THE RECORDER

1 Press

.

ACCESS MAIN MENU

SCREEN

2 Press MENU.

ACCESS MODE SET

3

SCREEN

Press %Þ to move the

MAIN MENU

highlight bar (pointer) to

MODE SET

"MODE SET", then press

AUTO CH SET

OK or #.

MANUAL CH SET

INITIAL SET

[5°] =

[MENU] : EXIT

4

SELECT DIRECT REC MODE

Press %Þ to move the

MODE SET

highlight bar (pointer) to

B. E. S. T.

ON

"DIRECT REC", then press

PICTURE CONTROL

AUTO

OK or #to set to "ON".

AUTO TIMER

OFF

O. S. D.

ON

DIRECT REC

ON

POWER SAVE

ON

AV2 SELECT

AV2

NEXT PAGE

[5°] =

[MENU] : EXIT

RETURN TO NORMAL

SCREEN

5 Press MENU.

NOTES:

•If "DIRECT REC" is set to "OFF", the RECORD button functions as described in "Basic Recording" (☞ pg. 17) .

•During the Direct Rec, "– –" appears on the display panel.

•When you perform T-V LINK functions, be sure to use the fully-wired 21-pin SCART cable.

Image 11

Contents HR-J313EU Do not place the recorder Safety PrecautionsFor Italy Connect Recorder to Mains Check ContentsBasic Connections Situate RecorderIf you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelThis Language CodeVia an RF cable only RF connection Your TV to the Video Channel. Refer toENU Preset DownloadJust Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Return to Normal Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPower Save Mode NexTView Link TV Auto Power OnLink Functions LI NKCounter and tape remaining time readings will be incorrect Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointSearch Playback FeaturesPlayback Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyRepeat Playback Access Mode SET ScreenSelect Picture Control SET Mode EN PlaybackBasic Recording Display Remaining Time Recording FeaturesReset Counter Select Channel to WatchPress Record on the recorder Engage ITR ModeInstant Timer Recording ITR SET Recording Duration#to set to on or OFF S.T. Picture SystemPreparation S.T., then press OK orOr press Record on the recorder RecordingPlayback EN Timer Recording Timer ProgrammingSatellite Tuner Users Timer WarningTime Express Timer ProgrammingStart Time Enter Programme StopPress TV Prog + SET VPS/PDC ModeIf no VPS/PDC signal is detected from the station, VPS VPS/PDC RecordingNext programmes Check, Cancel And Replace ProgrammesPress ä Timer Press Again to check More information. Each Time you pressOn or OFF Auto TimerAuto TIMER, then press OK or #to select eitherBefore performing the following steps Select AV2 Select ModeREC Link indicator Automatic Satellite Programme RecordingSET RECORDER’S Input SET Edit ModeEdit From a Camcorder Make ConnectionsStart Source Player Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SPress %Þ to move the highlight bar pointer to AV2 Select AV2 Select SettingAV2 IN/DECODER connector RecorderBack of TV Connection To Satellite TunerEN System Connections Satellite Tuner UnitSet AV2 Select to AV2. pg DecoderSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderEnter Receiving Channel Position Number Showview SetupSubsidiary Settings EN NumberAuto Channel Set Access Auto CH SETEN SU Bsidiary Settings Tuner SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSwitch Stations Access Manual Channel SET ScreenPerform Tuning Access ManualTV Station And ID List SET Date and Time Clock SetTurn the Recorder on Channel position to the number representing Default setting is OFF. Set as desired by pressingRecorder is preset to receive clock setting SET Just ClockSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers EN Ä remain lit on the display panel. Is there Problem?Front View IndexRear View VCR, TV Prog +/-,TV +/-, TV Muting EN IndexIN/OUT x 1, IN/DECODER x Speci FicationsRotary two-head herical scan Ex. Francais is selected for Belgium Auto Set Up referring to the display panel