JVC HR-J313EU specifications Colour System Set, Mode, About Ntsc Playback

Page 12

12EN

INFORMATIONONCOLOURSYSTEM

Colour System Set

1 2 3

2

4 5 6

7 8 9

0

4

1

?

OK

MENU

NOTES:

About NTSC Playback

●Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

●The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

●The counter and tape remaining time readings will be incorrect.

●During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

●Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM* signals on this recorder. Follow the procedure below to select the appropriate colour system.

*SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the designation for tapes with SECAM signals that have been recorded on a MESECAM-compatible PAL video cassette recorder.

TURN ON THE RECORDER

1 Press					.
1 Press					.
	ACCESS MAIN MENU
	SCREEN
2 Press MENU.
	ACCESS MODE SET SCREEN
Press %Þ to move the						MAIN MENU
	highlight bar (pointer) to
3 "MODE SET", then press						MODE SET
3 "MODE SET", then press						AUTO CH SET
	OK or #.					MANUAL CH SET
						INITIAL SET

						[5°] =
						[MENU] : EXIT

	SELECT COLOUR SYSTEM
	MODE
Press %Þ to move the						MODE SET
	highlight bar (pointer) to					PREVIOUS PAGE
4 "COLOUR SYSTEM", then						COLOUR SYSTEM PAL/NTSC
4 "COLOUR SYSTEM", then
	press OK or #to select the
	appropriate colour system.

						[5°] =
						[MENU] : EXIT

a- PAL/NTSC: To record PAL signals, or play back a PAL or NTSC tape.

b- MESECAM: To record SECAM signals, or play back a MESECAM tape.

RETURN TO NORMAL

SCREEN

5 Press MENU.

Image 12

Contents HR-J313EU Safety Precautions For ItalyDo not place the recorder Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Via an RF cable only RF connectionYour TV to the Video Channel. Refer to ThisPreset Download ENUIf both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage Access Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenPower Save Mode TV Auto Power On Link FunctionsLI NK NexTView LinkColour System Set ModeAbout Ntsc Playback Counter and tape remaining time readings will be incorrectBasic Playback Load a CassettePoint Start PlaybackPlayback Features PlaybackSearch Adjust Tracking Override Automatic TrackingManually Return to AutomaticAccess Mode SET Screen Select Picture Control SET ModeEN Playback Repeat PlaybackBasic Recording Recording Features Reset CounterSelect Channel to Watch Display Remaining TimeEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderS.T. Picture System PreparationS.T., then press OK or #to set to on or OFFRecording PlaybackOr press Record on the recorder Timer Programming EN Timer RecordingTimer Warning Satellite Tuner UsersExpress Timer Programming Start TimeEnter Programme Stop TimeSET VPS/PDC Mode If no VPS/PDC signal is detected from the station, VPSVPS/PDC Recording Press TV Prog +Check, Cancel And Replace Programmes Press ä TimerPress Again to check More information. Each Time you press Next programmesAuto Timer Auto TIMER, then pressOK or #to select either On or OFFSelect AV2 Select Mode REC Link indicatorAutomatic Satellite Programme Recording Before performing the following stepsSET Edit Mode Edit From a CamcorderMake Connections SET RECORDER’S InputInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerAV2 Select Setting AV2 IN/DECODER connectorRecorder Press %Þ to move the highlight bar pointer to AV2 SelectConnection To Satellite Tuner EN System ConnectionsSatellite Tuner Unit Back of TVDecoder Set AV2 Select to AV2. pgConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerShowview Setup Subsidiary Settings ENNumber Enter Receiving Channel Position NumberAccess Auto CH SET EN SU Bsidiary SettingsTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move beginsAccess Manual Channel SET Screen Perform TuningAccess Manual Switch StationsTV Station And ID List Clock Set Turn the Recorder onSET Date and Time Default setting is OFF. Set as desired by pressing Recorder is preset to receive clock settingSET Just Clock Channel position to the number representingAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output SystemTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and Answers ENIndex Front ViewRear View EN Index VCR, TV Prog +/-,TV +/-, TV MutingSpeci Fications Rotary two-head herical scanIN/OUT x 1, IN/DECODER x Auto Set Up referring to the display panel Ex. Francais is selected for Belgium