JVC HR-J313EU Automatic Satellite Programme Recording, Select AV2 Select Mode, REC Link indicator

Page 28

28ENTIMERRECORDING(cont.)

Automatic

Satellite

Programme

Recording

DISPLAY

STANDBY/ON

TIMER

REC LINK

TV PROG

REC LINK

REC LINK indicator

ATTENTION

●Be sure not to turn on the satellite tuner before the programme is executed; otherwise, the recorder will start recording when the satellite tuner's power is turned on.

●If you have connected another appliance other than a satellite tuner to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

This facility allows you record automatically a satellite programme which is timer-programmed on your external satellite tuner. Connect a satellite tuner to the recorder's AV2 IN/DECODER connector (☞ pg. 32) and programme the timer on the satellite tuner; the recorder starts recording when the signals input from the satellite tuner to the AV2 IN/DECODER connector, and when there is no input signals the recorder stops recording and the power shuts off.

Before performing the following steps:

●Make sure the satellite tuner is connected to the recorder's AV2 IN/DECODER connector. (☞ pg. 32)

●Programme the timer on the satellite tuner.

●Insert a cassette with the safety tab in place.

SELECT AV2 SELECT MODE

1 Set "AV2 SELECT" to "AV2" (☞ pg. 31).

ENGAGE AUTO SATELLITE PROG REC MODE

2 Press and hold REC LINK on the recorder for about 2 seconds. The REC LINK indicator lights up and the recorder turns off automatically.

●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The REC LINK indicator goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

●Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only. (☞ pg. 33)

●For timer programming of the satellite tuner, refer to the instruction manual of the satellite tuner.

●Auto Satellite Prog recording is not possible if your satellite tuner does not have a timer.

●The REC LINK indicator blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengage the Auto Satellite Prog Rec mode.

●The B.E.S.T. system (☞ pg. 20) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 42) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite tuner, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Recording mode when the satellite tuner's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK indicator blinks. When the satellite tuner shuts off once and is turned back on again, the recorder starts recording.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●After Auto Satellite Programme recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (☞ pg. 15).

●You can also record a programme from your cable system in the same way if the system has a timer.

●When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK indicator does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 24) to timer-record a satellite programme.

* Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Page 27 Page 29
Image 28
Page 27 Page 29
Contents HR-J313EU For Italy Safety PrecautionsDo not place the recorder Check Contents Basic ConnectionsSituate Recorder Connect Recorder to MainsAuto Set Up EN Initial SettingsIf you are referring to the front display panel If you are referring to the on-screen displayLanguage Code Via an RF cable only RF connectionYour TV to the Video Channel. Refer to ThisPreset Download ENUIf both auto channel set and auto clock set have failed Language for the on-screen displayJust Clock Just Clock onLanguage Access Main Menu Screen ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Return to Normal ScreenPower Save Mode TV Auto Power On Link FunctionsLI NK NexTView LinkColour System Set ModeAbout Ntsc Playback Counter and tape remaining time readings will be incorrectBasic Playback Load a CassettePoint Start PlaybackPlayback Playback FeaturesSearch Adjust Tracking Override Automatic TrackingManually Return to AutomaticAccess Mode SET Screen Select Picture Control SET ModeEN Playback Repeat PlaybackBasic Recording Recording Features Reset CounterSelect Channel to Watch Display Remaining TimeEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderS.T. Picture System PreparationS.T., then press OK or #to set to on or OFFPlayback RecordingOr press Record on the recorder Timer Programming EN Timer RecordingTimer Warning Satellite Tuner UsersExpress Timer Programming Start TimeEnter Programme Stop TimeSET VPS/PDC Mode If no VPS/PDC signal is detected from the station, VPSVPS/PDC Recording Press TV Prog +Check, Cancel And Replace Programmes Press ä TimerPress Again to check More information. Each Time you press Next programmesAuto Timer Auto TIMER, then pressOK or #to select either On or OFFSelect AV2 Select Mode REC Link indicatorAutomatic Satellite Programme Recording Before performing the following stepsSET Edit Mode Edit From a CamcorderMake Connections SET RECORDER’S InputInput Mode Edit To Or From Another Video RecorderSET Recording DECK’S Start Source PlayerAV2 Select Setting AV2 IN/DECODER connectorRecorder Press %Þ to move the highlight bar pointer to AV2 SelectConnection To Satellite Tuner EN System ConnectionsSatellite Tuner Unit Back of TVDecoder Set AV2 Select to AV2. pgConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerShowview Setup Subsidiary Settings ENNumber Enter Receiving Channel Position NumberAccess Auto CH SET EN SU Bsidiary SettingsTuner Set Auto Channel SetPerform Auto Channel SET View Confirmation ScreenSU Bsidiary Settings Storing Channels ManuallyWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Press %Þ @ #until the item you want to move beginsAccess Manual Channel SET Screen Perform TuningAccess Manual Switch StationsTV Station And ID List Turn the Recorder on Clock SetSET Date and Time Default setting is OFF. Set as desired by pressing Recorder is preset to receive clock settingSET Just Clock Channel position to the number representingAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET RF Output SystemTroubleshooting EN Timer Recording RoubleshootingÄ remain lit on the display panel. Is there Problem? Quest Ions and Answers ENIndex Front ViewRear View EN Index VCR, TV Prog +/-,TV +/-, TV MutingRotary two-head herical scan Speci FicationsIN/OUT x 1, IN/DECODER x Auto Set Up referring to the display panel Ex. Francais is selected for Belgium
Top Page Image Contents