JVC HR-J313EU Quest Ions and Answers EN, Ä remain lit on the display panel. Is there Problem?

Page 47

QUESTIONSANDANSWERSEN47

PLAYBACK

 

RECORDING

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during multi-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder goes to its Stop mode auto- matically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning.

TIMER RECORDING

Q. "" and "ä" remain lit on the display panel. Is there

aproblem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the programme or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 47
Contents HR-J313EU Do not place the recorder Safety PrecautionsFor Italy Connect Recorder to Mains Check ContentsBasic Connections Situate RecorderIf you are referring to the on-screen display Auto Set UpEN Initial Settings If you are referring to the front display panelThis Language CodeVia an RF cable only RF connection Your TV to the Video Channel. Refer toENU Preset DownloadJust Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Return to Normal Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPower Save Mode NexTView Link TV Auto Power OnLink Functions LI NKCounter and tape remaining time readings will be incorrect Colour System SetMode About Ntsc PlaybackStart Playback Basic PlaybackLoad a Cassette PointSearch Playback FeaturesPlayback Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyRepeat Playback Access Mode SET ScreenSelect Picture Control SET Mode EN PlaybackBasic Recording Display Remaining Time Recording FeaturesReset Counter Select Channel to WatchPress Record on the recorder Engage ITR ModeInstant Timer Recording ITR SET Recording Duration#to set to on or OFF S.T. Picture SystemPreparation S.T., then press OK orOr press Record on the recorder RecordingPlayback EN Timer Recording Timer ProgrammingSatellite Tuner Users Timer WarningTime Express Timer ProgrammingStart Time Enter Programme StopPress TV Prog + SET VPS/PDC ModeIf no VPS/PDC signal is detected from the station, VPS VPS/PDC RecordingNext programmes Check, Cancel And Replace ProgrammesPress ä Timer Press Again to check More information. Each Time you pressOn or OFF Auto TimerAuto TIMER, then press OK or #to select eitherBefore performing the following steps Select AV2 Select ModeREC Link indicator Automatic Satellite Programme RecordingSET RECORDER’S Input SET Edit ModeEdit From a Camcorder Make ConnectionsStart Source Player Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SPress %Þ to move the highlight bar pointer to AV2 Select AV2 Select SettingAV2 IN/DECODER connector RecorderBack of TV Connection To Satellite TunerEN System Connections Satellite Tuner UnitSet AV2 Select to AV2. pg DecoderSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderEnter Receiving Channel Position Number Showview SetupSubsidiary Settings EN NumberAuto Channel Set Access Auto CH SETEN SU Bsidiary Settings Tuner SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually SU Bsidiary SettingsPress %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSwitch Stations Access Manual Channel SET ScreenPerform Tuning Access ManualTV Station And ID List SET Date and Time Clock SetTurn the Recorder on Channel position to the number representing Default setting is OFF. Set as desired by pressingRecorder is preset to receive clock setting SET Just ClockSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetTroubleshooting EN Roubleshooting Timer RecordingQuest Ions and Answers EN Ä remain lit on the display panel. Is there Problem?Front View IndexRear View VCR, TV Prog +/-,TV +/-, TV Muting EN IndexIN/OUT x 1, IN/DECODER x Speci FicationsRotary two-head herical scan Ex. Francais is selected for Belgium Auto Set Up referring to the display panel